无损检测工艺规程(超 声 波 检 验)-双语版
NJBST Co.,Ltd.
QCD-013
Rev.:0
Page:7 of 12
Title: ULTRASONIC EXAMINATION PROCEDURE 6.3.1 扫描范围校正 6.3.1 Sweep Range Correction. If a point on the DAC curve has moved on the sweep line more than 如果 DAC 曲线上某一点沿扫描线 10% of the sweep reading or 5% of full sweep, whichever is greater, 的偏移超过扫描分格读数 10%或 correct the sweep range calibration and note the correction in the 满刻度 5%(取其中较大者),则需 examination record. If reflectors are recorded on the data sheets, those 修正扫描范围的校正,并在检验 data sheets shall be voided and a new calibration shall be recorded. All 记录中注明这一数值.如果已将 recorded indications since the last valid calibration or calibration 体记录在数据表中,则这些数据 check shall be reexamined with the corrected calibration and their 表要作废,并记录新的校正.从 上一 有效的校正或校正核查以 values shall be changed on the data sheets. 来所记录的全部信号,均需用经 6.3.2 DAC Correction If a point on the distance-amplitude correction (DAC)curve has 修正的校正重作检验,且数据表 decreased 20% or 2 dB of its amplitude, all date sheets since the last 中的这些数值也要作修改. calibration or calibration check shall be marked void. An area covered 6.3.2 DAC 校正 by the voided data shall be reexamined. If any point of the distance 若 DAC 曲线上某一点其波幅减 amlitude correction (DAC) curve has increased more than 20% or 2 少 20%或 2dB ,则从上一次校正 dB of its amplitude, all recorded indications since the last valid 或校正核查以来的所有数据表均 calibration or calibration check shall be reexamined with the corrected 应标注取消.应进行新的校准和 记录,并对数据所包括区域重作 calibration and their values shall be changed on the data sheets. 检验.若 DAC 曲线上任何点其波 7. EXAMINATION 幅增加大于 20%或 2dB, 则从上 7.1 Surface preparation 一次有效校正或校正核查的所有 7.1.1 Base Metal The base metal on each side of the weld shall be free of weld 记录信号,应重按修正的校准检 spatter, surface irregularities, or foreign matter that might interfere 验,其数值也应在数据表上更改. 7. 检验 with the examination. 7.1 表面准备 7.1.2 Weld Metal Where the weld surface interferes with the examination, the 7.1.1 母材 焊缝两侧母材应无焊接飞溅, weld shall be prepared as needed to permit examination. 表面不规则或妨碍探伤的其他杂 7.2 Couplant 物. The couplant used in UT examination should be as same as that used in calibration. The No. 20 motor oil or glycerin or paste(C.M.C) 7.1.2 焊缝 若焊缝表面状态妨碍探伤,应 shall be recommended to use. 作适当修磨. 7.3 Scanning Requirements 7.2 耦合 7.3.1 Angle Beam Scann
ing 焊缝 UT 用的耦合剂应与试块 7.3.1.1 Scanning for Reflectors Oriented Parallel to the Weld 校验时用的相同. 推荐用 20#机油 The angle beam shall be directed at approximate right angles to the weld axis from two directions where possible. The search unit shall be 或甘油或化学浆糊(C.M.C). manipulated so that the ultrasonic energy passes through the required 7.3 扫查要求 volumes of weld and adjacent base metal. The scanning shall be 7.3.1 斜探头扫查 performed at a gain setting at least two times the primary reference 7.3.1.1 用斜射波探测平行于缝的 level. Evaluation shall be performed with respect to the primary 反射体. 斜声束方向应大致与焊缝轴 reference level. 线成直角.如有可能,要从两个 7.3.1.2 Scanning for Reflectors Oriented Transverse to Weld The angle beam shall be directed essentially parallel to the weld 方向进行.要适当操作探头,使 超声能量能经过所需检查的焊缝 axis. The search unit shall be manipulated so that the angle beam 和邻近母材金属的体积.扫查中, passes through the required volumes of weld and adjacent base metal 应将增益调整到比基准灵敏度至 specified by the referencing Code Section. The scanning shall be 少高一倍.应参照灵敏度基准作 performed at a gain setting at least two times the primary reference 出评定. level. Evaluation shall be performed with respect to the primary reference level. The search unit shall be rotated 180 deg. and the examination repeated.

超声波检测工艺规程_机械/仪表_工程科技_专业资料...承压设备无损检测 GB50235-1997 工业金属管道工程... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程1_机械/仪表_工程科技_专业资料...无 损 检 测 工 艺 规 程 ZW09-04-08 总份...标准 11 条标准 11.3 附录C 超 声 波 探 伤 ...
无损探伤工艺及超声波应用_信息与通信_工程科技_...无损检测工艺规程无损检测工艺规程是按本单位的受检...焊缝的超声波检测———可用直射声束法或斜射声束法...
单斜探头、双晶探头等,在达到所检 工件的最大检测声程时,其有效灵敏度余量≥... 超声波探伤工艺规程 9页 免费 无损检测工艺规程(液体渗... 9页 免费 无损...
超声波探伤操 作工艺规程 1. 主题内容与适用范围 ...2 引用标准 JB4730-2005《 承压设备无损检测》 JB...a 仪器和探头的组合灵敏度:在达到所检工件最大声...
本规程规定了无损检测人员应具备的资格,本公司所采用的四种无损检测方法射线检 测、超声检测、磁粉检测和渗透检测,检测设备,检测工艺,检测时机,验收标准及档案的 ...
探伤工艺规范 超声波探伤工艺规范 磁粉探伤工艺规范 ...d. 探头主声束应无双峰、无偏斜。 2.2.2 采用...是被检焊缝的厚度,两厚度不等的焊接件,T 则是两...
超声波检测工艺规程_机械/仪表_工程科技_专业资料...3 引用标准 JB4730《压力容器无损检测》 GB150《... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程_六年级其它课程_其它课程_小学...1.6 校准 校准在基准试块上进行,使超声波主声束...2.8.8 复验 当决定复验时,必须对被检面进行...
超声无损检测通用...超声波检测通用工艺规程编制: 编制: 审核: 审核: ...按表2选择和使用 DAC 曲线灵敏度,按表3进行验 收...
热门文档