无损检测工艺规程(超 声 波 检 验)-双语版
NJBST Co.,Ltd.
QCD-013
Rev.:0
Page:9 of 12 a. 检验规程; b. 超声检验系统(设备) c. 探伤人员资格,等级; d. 验证校验用表格; e. 焊缝或扫查范围标志和位置; f. 进行检验的表面; g. 探到的缺陷及已探明区的示 图或记录; h. 检验日期和时间; i. 耦合剂; j. 基准校正试块识别标志; k. 表面状况; l. 频率; m. 专用设备 10.3 评定记录 对各种缺陷信号进行任何评
定 的记录,均应予保存和编成文件. 10.4 检验报告 应作出 UT 报告.报告内容应包 括:被检焊缝及草图,缺陷位置, 探伤人员及资格.报告应经另一 NDE 人员Ⅱ级或Ⅲ级人员审核并 由Ⅲ级批准后送交 AI 审查和验 收. 10.5 所用 UT 记录,报告 和工艺 卡表式见 10-12 和附录 1,2. 11. 后清理 超声检验后,如有要求,应作 后清理,将被检区表面涂布的耦 合剂除干净.
Title: ULTRASONIC EXAMINATION PROCEDURE (a) procedure (b) ultrasonic examination system (equipment) (c) examination personnel identity and level if required by referencing Code Section (d) calibration sheet identity (e) identification and location of weld or volume scanned (f) surface from which examination is conducted (g) map or record of indication detected or areas clear (h) date and time examinations were performed (i) couplant (j) basic calibration block identification (k) surface condition (l) frequency (m) special equipment 10.3 Evaluation Record Records of any evaluations of indication shall be maintained and documented. 10.4 REPORTS A report of the examinations shall be made. The report shall include a record indicating the weld(s) or volume examined (this may be marked-up sketched), the location of each recorded reflector, and the identification of the operator who carried out each examination or part. The report shall be reviewed by another NDE Level Ⅱor Level Ⅲ and approved by NDE level Ⅲ Examiner prior to submitting to AI for review and acceptance. 10.5 The forms of UT record, report and specific instruction card see page 10-12 and Appendix 1,2. 11. Post-examination cleaning After ultrasonic examination, the post cleaning shall be done for removing the couplant on the examined area, if it is required.

超声波检测工艺规程_机械/仪表_工程科技_专业资料...承压设备无损检测 GB50235-1997 工业金属管道工程... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程1_机械/仪表_工程科技_专业资料...无 损 检 测 工 艺 规 程 ZW09-04-08 总份...标准 11 条标准 11.3 附录C 超 声 波 探 伤 ...
无损探伤工艺及超声波应用_信息与通信_工程科技_...无损检测工艺规程无损检测工艺规程是按本单位的受检...焊缝的超声波检测———可用直射声束法或斜射声束法...
单斜探头、双晶探头等,在达到所检 工件的最大检测声程时,其有效灵敏度余量≥... 超声波探伤工艺规程 9页 免费 无损检测工艺规程(液体渗... 9页 免费 无损...
超声波探伤操 作工艺规程 1. 主题内容与适用范围 ...2 引用标准 JB4730-2005《 承压设备无损检测》 JB...a 仪器和探头的组合灵敏度:在达到所检工件最大声...
本规程规定了无损检测人员应具备的资格,本公司所采用的四种无损检测方法射线检 测、超声检测、磁粉检测和渗透检测,检测设备,检测工艺,检测时机,验收标准及档案的 ...
探伤工艺规范 超声波探伤工艺规范 磁粉探伤工艺规范 ...d. 探头主声束应无双峰、无偏斜。 2.2.2 采用...是被检焊缝的厚度,两厚度不等的焊接件,T 则是两...
超声波检测工艺规程_机械/仪表_工程科技_专业资料...3 引用标准 JB4730《压力容器无损检测》 GB150《... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程_六年级其它课程_其它课程_小学...1.6 校准 校准在基准试块上进行,使超声波主声束...2.8.8 复验 当决定复验时,必须对被检面进行...
超声无损检测通用...超声波检测通用工艺规程编制: 编制: 审核: 审核: ...按表2选择和使用 DAC 曲线灵敏度,按表3进行验 收...
热门文档