无损检测工艺规程(超 声 波 检 验)-双语版
NJBST Co.,Ltd.
QCD-013
Rev.:0
Page:6 of 12
糙度. 5.2.5 Block Quality. The calibration block material shall be completely 5.2.5 试块质量. 校正试块材料应使 在声束到达多 examined with a straight beam search unit. Areas that contain an 用直探头作全面检查. 不得有超过 indication exceeding the remaining back reflection shall be excluded 种校正反射体的声路中. from the beam paths required to reach the various calibration 底波反射的信号存在. 5.3 校正反射体 reflectors. 5.3.1 基本校正反射体 5.3 Calibration Reflectors 校正反射体按图 1 规定. 5.3.1 Basic Calibration Reflectors 5.3.2 直径≤20in(508mm)的材料, 基 The calibration reflectors are specified in Fig.1 除本规程另有说明 5.3.2 Welds in Materials with Diameters 20 in. (508mm) and less. 本试
块应为曲面. 外,一个单一曲面的基本校正试块, The basic calibration block shall be curved for materials with diameters 20 in. (508mm)and less. Except where otherwise stated in 可用来校正表面曲率范围为 0.9~1.5 this procedure a single curved basic calibration block may be used to 倍基本校正试块直径的检验. calibrate the examination on surfaces in the range of curvature from 6. 系统校验 6.1 斜探头校验(横波) 0.9 to 1.5 times the basic calibration block diameter 应作下列测定: 6. SYSTEM CALIBRATION (GENERAL) 6.1 Angle Beam Calibration(Transversal wave) as applicable the (a) 扫查范围校正 (b) 距离-波幅校正(DAC) calibration shall provide the following measurements: (C) 位置校正 (a) sweep range calibration; (d) 基本校正试块中横孔回波幅度 (b) distance-amplitude correction(DAC); 的测定. (C) position calibration; (d) echo amplitude measurement from the transverse drilled hole in the 6.2 直探头校验 应作下列测定 basic calibration block. (a) 扫查范围校正: 6.2 Straight Beam Calibration (b) 距离-波幅校正(DAC) The calibration shall provide the following measurements: 6.3 校验确认 (a) sweep range calibration; 使用仪器前, 应按被检厚度范围进 (b) distance-amplitude correction(DAC). 行校准. 6.3 Calibration Confirmation representative of the surface finishes on the component.
Title: ULTRASONIC EXAMINATION PROCEDURE 校正试块 on the side of the weld from which the examination will be conducted: 涉及到两种以上的壁厚时, if the examination will be conducted from both sides, calibration 厚度应按焊缝平均厚度确定. reflectors shall be provided in both materials. Where two or more base 5.2.2 堆焊层 当部件材料有堆焊层时, 试块也应 material thicknesses are involved, the calibration block thickness shall 有堆层, 其堆焊层规程应与产品零件 be determined by the average thickness of the weld. 一样. 若不能采用自动焊方法, 则应 5.2.2 Clad . 最好是采用切除 Where the component material is clad, the block shall be clad by 用手工焊方法堆焊. 的或延长部分未除去堆焊的部件材 the same welding procedure as the production part. Where the automatic method is impractical, deposition of clad shall be by the 料. manual method. It is desirable to have component materials which 5.2.3 热处理 校正试块应按材料牌号要求,至少 have been clad before the drop outs or prolongations are removed. 若校正试块 5.2.3 Heat Treatment. The calibration block shall receive at least the 作最低程度的回火处理. 中含有焊缝, 则还需作至少 2 小时的 minimum tempering treatment required by the material specification for the type and grade, and also a postweld heat treatment of at least 2 焊后热处理. 5.2.4 表面粗糙度 hr, if the calibration block contains weld(s). 5.2.4 Surface Finish. The finish on the surfaces of the block shall be 试块表面粗糙度
应代表工件表面粗
Calibration shall be performed prior to use of the system in the thickness range under examination.

超声波检测工艺规程_机械/仪表_工程科技_专业资料...承压设备无损检测 GB50235-1997 工业金属管道工程... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程1_机械/仪表_工程科技_专业资料...无 损 检 测 工 艺 规 程 ZW09-04-08 总份...标准 11 条标准 11.3 附录C 超 声 波 探 伤 ...
无损探伤工艺及超声波应用_信息与通信_工程科技_...无损检测工艺规程无损检测工艺规程是按本单位的受检...焊缝的超声波检测———可用直射声束法或斜射声束法...
单斜探头、双晶探头等,在达到所检 工件的最大检测声程时,其有效灵敏度余量≥... 超声波探伤工艺规程 9页 免费 无损检测工艺规程(液体渗... 9页 免费 无损...
超声波探伤操 作工艺规程 1. 主题内容与适用范围 ...2 引用标准 JB4730-2005《 承压设备无损检测》 JB...a 仪器和探头的组合灵敏度:在达到所检工件最大声...
本规程规定了无损检测人员应具备的资格,本公司所采用的四种无损检测方法射线检 测、超声检测、磁粉检测和渗透检测,检测设备,检测工艺,检测时机,验收标准及档案的 ...
探伤工艺规范 超声波探伤工艺规范 磁粉探伤工艺规范 ...d. 探头主声束应无双峰、无偏斜。 2.2.2 采用...是被检焊缝的厚度,两厚度不等的焊接件,T 则是两...
超声波检测工艺规程_机械/仪表_工程科技_专业资料...3 引用标准 JB4730《压力容器无损检测》 GB150《... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程_六年级其它课程_其它课程_小学...1.6 校准 校准在基准试块上进行,使超声波主声束...2.8.8 复验 当决定复验时,必须对被检面进行...
超声无损检测通用...超声波检测通用工艺规程编制: 编制: 审核: 审核: ...按表2选择和使用 DAC 曲线灵敏度,按表3进行验 收...
热门文档