文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > divergence detected in AMG solver pressure correction,fluent典型错误
侵权投诉

divergence detected in AMG solver pressure correction,fluent典型错误

选填,简要介绍文档的主要内容,方便文档被更多人浏览和下载。

问题:8-31-rke-steady-4-0.8运行至11000迭代步是报错“divergence detected in AMG solver: pressure correction”(补充:每个工况均遇到此类情况,原因尚未找到,暂时解决办法是将压力松弛因子从0.3改为0.1);

This error is reported when Fluent is not able to converge the solution。The

residuals are not converged。This error may come due to various reasons like improper mesh,improper boundary conditions,wrong material and improper solution settings。It is advisable to re check the entire case when one encounters this error。 解答:

以上老外对这个问题的回复,确实很多客户遇到过这样的问题,原因是多方面的,主要原因集中在网格质量差和边界条件的不合理。

对于你的问题,如果之前都没有错误,到一定计算步才出现这样的问题,说明不是边条的问题,问题可能出在局部的网格上面,你将压力松弛因子调小,增加跌代次数,减小了误差,是解决问题的方法之一。

如果想彻底回避这样的问题出现,建议在网格上还需要下点工夫!

附:老外对类似问题的回复,你可以参考一下。

I try to study the turbulence inside a vertical cylinder. In a first time, I take the

case of steady flow. The air is introduced axially from below, deflected by means of a small conical deflector and thanks to the geometry of the chamber the air goes up into the cylinder. I take the ideal gas law, k-epsilon model, inlet and outlet pressure for boundary conditions. My problem is that I have directly the message "divergence detected in AMG solver : k when I want to iterate. I try a lot of solutions I have find in this forum without any result. Could anyone help me? Thanks

in advance Check your hardware, especially RAM sockets. I have experience, that this could be initiated by some bad memory address sectors.

I had a similar problem, but with pressure correction. I found that I had some

highly skewed cells. Once I corrected the highly skewed cells by adapting the

iso-values of cell skewness my case began to iterate.

Perhaps this may be your problem. First initialize the solution and then go to

contours grid and select equiangle skew and click compute to get you min and maxs. Having skewed cells of 0.9 or higher isn';t good, as in my case.

Hope this helps I have check the skewed cells but it appears that in my case, this number is lower than 0.4 Is it too high?

Hi. I have a simulation of a supersonic-valve running but the program shows me this message: divergence detected in AMG solver: temperature I tried to rise the limits for temperature and other solution limits but nothing has helped so far Does anyone what to do thanks

Try to use more conservative Under-relaxation factor. I had the same problem with a wing in a transonic flight. According to me the segregated solver is not suitable for the conditions with high compressibility. Let me know if you succeed in using the segregated and how...

第1页

你可能喜欢

  • 经典教程
  • 时间步长
  • 建筑规划
  • 多孔介质
  • 中国共产党的指导思想
  • 湍流模型

热门文档

相关文档

  • divergence detected in AMG solver

    8-31-rke-steady-4-0.8 运行至 11000 迭代步是报错“divergence detected in AMG solver: pressure correction”(补充:每个工况均遇到此类情况,原因尚未找到,...

  • [Fluent] Solver error原因及处理方法综整

    出现时机 Error: divergence detected in AMG solver Error: Object: () / ...I had a similar problem, but with pressure correction. I found that I ...

  • fluent常见错误

    fluent常见错误_能源/化工_工程科技_专业资料。http...Reverse flow in XX faces on pressure-outlet-X ...divergence detected in AMG solver.# G- ]6 o0...

  • fluent例子

    fluent例子_计算机软件及应用_IT/计算机_专业资料。...11 1451 reversed flow in 8 faces on pressure-...Error: divergence detected in AMG solver: w-...

  • Volume fraction gradient in eulerian model

    when the fluent is divergence,the velocity or pressure is very large,and give: Error: divergence detected in AMG solver: pressure correction Error Object:...

  • fluent例子

    fluent例子_计算机软件及应用_IT/计算机_专业资料。...11 1451 reversed flow in 8 faces on pressure-...Error: divergence detected in AMG solver: w-...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email