选填,简要介绍文档的主要内容,方便文档被更多人浏览和下载。
I suggest using the coupled solver,Your problem will vanish... Hope to hear good news from you soon.
Luca this will be something wrong with the either boundary condition or with
model selection, generally if things are right fluent just converges fine without any warning or problem.
in my opinion these are the signs that you are doing something wrong in setting up the case, look closely
Hi, I have the same problem, and couldn't solve it by using the coupled solver. Is there any other possible way. I am simulating office room problem. It seems very simple but on every stage it is creating problems for me. I am going to try to change the underrelaxation. lets see what comes up.
Thanks long ago, one of my friend was doing CFD analysis of a kitchen,, using coupled solver, and he faced the same problem, for some time he didn’t get the
converged results. Finally when I looked at his mesh. It seemed the problem is with the mesh not with the solver settings. I suggested him to make mesh more finer, and viola it gave results in one run, without any problem. so moral of the story check your mesh.
My mesh is quite fine, but I will try more finer mesh. Thanks then it shall
converge ..anyway have you tried using segregated solver, how the results with that
Error: Divergence detected in AMG solver? Posted By: frank Date: Sun, 16 Jan 2005, 3:58 p.m. What does mean and how do i fix it? I am runing a rosseland
radiation model and it wont run past 1 iteration.
Frank you are using the segregated solver, so you must reduce the under
relaxation factor as you can. You could have a grid issue concerning high skewness. This can be checked by going to contours grid cell equiangle skew and select compute and check the min and max. You should be below 0.9. If over then this could be your problem. It has happened to me a couple of times. thanks a million i will try this...
frank AMG solver: k divergence? Posted By: Robert Date: Sun, 9 Mar 2003,
11:23 a.m. How do I remedy a divergence with this message. This is for scramjet
combustion in 2D with injectors on both the top and bottom. Is there any way to look up error messages?
reduce underalaxtion factor.
I have tried reducing the underelaxation factors but the divergence persists. Any other suggestions? Perhaps in the AMG solver Menu? It looks like a problem with your boundary conditions, be sure they're compatible with each other and consistent with the physics of what you';re trying to simulate, I think you'd better don't touch anything in the AMG menu, unless you know exactly what you're doing, It is my opinion, if this could help.
请求高手指点:循环流化床中非稳态气固两相流计算,使用欧拉双流体模型,K-E湍流模型,网格质量<0.55。先计算了层流稳态,残差小于0.01时转为湍流
8-31-rke-steady-4-0.8 运行至 11000 迭代步是报错“divergence detected in AMG solver: pressure correction”(补充:每个工况均遇到此类情况,原因尚未找到,...
出现时机 Error: divergence detected in AMG solver Error: Object: () / ...I had a similar problem, but with pressure correction. I found that I ...
fluent常见错误_能源/化工_工程科技_专业资料。http...Reverse flow in XX faces on pressure-outlet-X ...divergence detected in AMG solver.# G- ]6 o0...
fluent例子_计算机软件及应用_IT/计算机_专业资料。...11 1451 reversed flow in 8 faces on pressure-...Error: divergence detected in AMG solver: w-...
when the fluent is divergence,the velocity or pressure is very large,and give: Error: divergence detected in AMG solver: pressure correction Error Object:...
fluent例子_计算机软件及应用_IT/计算机_专业资料。...11 1451 reversed flow in 8 faces on pressure-...Error: divergence detected in AMG solver: w-...
热门文档