TRANSACTIONS ON SEMICONDUCTOR MANUFACTURING, VOL. 7, NO. 3, AUGUST 1994
393
H. Shimada, M. Onodera, T. Nonaka, K.Hirose, and T. Ohmi,“Opti- acceptable production criteria today is 4.5 mil bond pad pitches,< 4 mizing resist development process for reliable fine-pattem formation,” mil pad openings, and 200 mil wires. Compare these criteria to those Extended Abstracts, 179th Electrochem. Soc. Meet., Washington, JX,that existed just two years ago (6.2 mil bond pad pitches, r4 mil pad Abstract 445, May 1991, pp. 680-681. H. Shimada, K. Hirose, S. Shimomura, M. Onodera, and T. Ohmi, openings, and 100 mil maximum wire lengths). The capability to ensure high yields on these small die in the high“Residual-surfactant-free photoresist development process,” J. Electrochem. Soc., vol. 139, no. 6, pp. 1721-1730, June 1992. pin count plastic packages at wire bond however is impacted by the H. Shimada, S. Shimomura, K. Hirose, M. Onodera, and T. Ohmi, assembly engineer’s ability to characterize and control the wire bonds.“Optimization of photolithography developing process without residual surfactant on surfaces,” IEICE Trans. Electron., vol. E75-C, no. 7, pp. The long wire bonds associated with these small die require a high loop profile to prevent wire sagging. The fine pitch bond pads force 844-851, July 1992. H. Shimada, S. Shimomura, K. Hirose, and T. Ohmi,“High-sensitivity the loop profile to be low in order to avoid damage to the adjacent and high-resolution contact hole patteming by enhanced-wettability bonding wire by the capillary side wall (Fig. 1).[l] developer,” Japan. J. Appl. Phys., vol. 32, no. IB, pp. 347-351, Jan. These apparently conflicting requirements must be evaluated in a 1993. E. J. Walker,“Reduction of photoresist standing-wave effects by post- designed experiment in order to be properly understood and charexposure bake,” IEEE Trans. Electron Devices, vol. ED-22, no. 7, pp. acterized. In a previous study, a response surface methodology was 464466, 1990. effectively used in evaluating the main effects and the interactions of H. Kikuyama, N. Miki, K. Saka, J. Takano, I. Kawanabe, M. Miyashita, bonding parameters on loop profile characterization and control.[2] and T. Ohmi,“Surface active buffered hydrogen fluoride having excellent wettability for ULSI processing,” IEEE Trans. Semiconduct. In this study, the“ideal” loop profile (Fig. 2) was established for a 175 mil 1.3 mil diameter gold wire. Manufact., vol. 3, no. 3, pp. 99-108, Aug. 1990. R. Nakano, M. Hirose, N. Santoh, K. Nakagawa, and K. Shigematsu, This paper expands on the experimental expertise gained in the“Effect of low-molecular-weight Novolak resin on microgrooves,” previous evaluation and determines if the same evaluation applies to Japan. J.AppZ. Phys., vol. 30, no. IIB, pp. 3121-3124, Nov. 1991. greater than 175 mil wire lengths. The data obtained demonstrates the changes in bonding parameters required in order to continue to p
roduce the“ideal” loop profile and further substantiates the methodology outlined. 1 . EXPERIMENTAL 1 Response S u~ a c e Methodology: As in the previous study a K&S 1484 gold ball wire bonder with a 10 degree bottleneck capillary and 1.3 mil gold wire were used. All wire bonds were fixed at either 175 mils or 200 mils by bonding to an aluminum metallized mirror chip epoxy die attached to a metric quad flat pack leadframe. For the sake of brevity all information discussed in this paper shall deal only with the 175 mil wire length results. The effects of the following bonding parameters: kink height (KH), reverse loop (RL), loop factor (LF), and vacuum (VA)-were analyzed. As suggested by K&S, loop trajectory was set as“1.” The other bond parameters: bond power, bond force, bond temperature, and bond time, were adjusted to ensure good first and second bond quality. A 25-run Central Composite Circumscribed (CCC) design, based on response surface methodology, provided information on main effects, interactions and a response surface[3]-[5]. Table I shows the bonding parameters and setting for each run in this evaluation. RSExplore and RSDiscover software by BBN Software Products Corporation was used in the experimental design and analysis of the results. Loop Profile Measuring Methodology: Fig. 3 shows the loop profile measurement points on the gold wire. The origin (0, 0,O) is at the center of the gold ball bond at pad level. Measurements starting at the front edge of the ball bond are made at one (1) mil intervals along the outside edge of the wire until the peak loop height is obtained. From that point on measurements were made at approximately ten (10) mil intervals until the second bond was reached. Data collection was performed using a measuring microscope at 400x with a Quadra-Chek QC-3300 Smart Box and a Macintosh SE computer link. X, Y, and Z coordinates were determined at each measurement location. These coordinates were transferred to the Macintosh as ASCII codes and translated into an Excel spreadsheet. The shape of each wire was then reconstructed for data extraction from an Excel chart.
Wire Bond Loop Profile Development for Fine Pitch-Long Wire Assembly R. Groover, W. K. Shu, and S. S. Lee Abstract- Die size reductions can be achieved through“optical shrinks,” compaction of existing layouts, or redesigns to finer fab geometries. For some die the limiting factors for die size reduction are bond pad pitch and bond pad size. In these“pad limited” designs, the circuitry is concentrated in the center of the die. Precious empty space exists between the bond pads in the periphery of the die and the circuitry in the die core. The only hope for die size reductions in these designs lies in advances in assembly technology that allow for reductions in bond pad pitches and bond pad size. Fine pitch assembly poses a number of challenges for conventional wire bond technology. Reducing bond pad pitch increases the probability of
ball shorting, bond wire shorting, and bond wire damage. On the other hand, decreasing the die size by reducing the bond pad pitch results in longer wire lengths thus limiting some assembly options such as moving to smaller diameter bonding wires. Wire loop profile becomes a critical factor for control in fine pitch assembly. In this paper a statistical design of experiment is used in developing a wire bond loop profile control. The effect of major bonding parameters, such as kink-height, reverse loop, loop factor, wire tension, and their impact on loop profle are analyzed. The results obtained define the bond parameter requirements that must be met in order to control the wire loop profile to optimize fine pitch wire bond assembly yields.
I. INTRODUCTION Improvements in wire bonder capabilities, bonding wire metallurgy, lead frame design, and engineering expertise continue to facilitate the manufacturability of small die in high pin count plastic packages. For example in 208 pin Metric Quad Flat Pack (MQFF’) Manuscript received November 20, 1991; revised September 9, 1993. The authors are with VLSI Technology, Inc., San Jose, CA 95131. IEEE Log Number 9214303.
0894-6507/94$04.0001994 IEEE

WIRE BOND PROCESS INTRODUCTION CONTENTS ASSEMBLY ...Multimode Transducer System Programmable profile, ...Bond Pad Pitch Ball Size Ball Thickness Loop ...
ASSEMBLY FLOW OF CIS ? Wire Bond Theory ? M/...2.5 um ?Fine Pitch Capability ?35 mm pitch @...loop Prepared pad By Hawk Long Source:NA Camtech...
Capillary interferes with 1st bond ? Used cap (PBGA 45um) with profile ... New Generation 4N wire for super-long loop, for fine pad pitch (Flex ...
file://C:\Wire-Bond-Inspection-Tools.html 9/17/03 Assembly - Wire ...D. Use the Fine/Coarse focus knobs to bring the top of the wire loop ...
Loop J-Wire II RF Loop II Security Bond II ...Long Wire, Fine Pitch, QFP, PLCC, SOJ, LOC,...J-Wire Loop Profile J-Wire GUI Screens Following...
UL loop ? by ESEC February 2004, High ...Assembly Solutions 10 CONFIDENTIAL Bond modes - IF...s due to small capillary IC ( fine pitch ) ?...
Wire Bond Loop Profile Development for Fine Pitch -Long Wire Assembly [J]...系统仿真学报,2006,18(11): 3058-3062。 作者简介 :周洪军(1985-),男,硕士...
PROFILE Z-axis EFO Ball bond Looping Search wedge Wedge bond Search ball ...long loop bonding Low temperature bonding Fine pitch / fine size bonding ...
ASM焊线(wire bond)摆线探索_机械/仪表_工程科技_专业资料。ASM焊线工艺探索...3 kink 的 loop profile 昨天用 BGA-last loop 打出来 的效果如左图, 这是...
Stitch Bond Enhancement For X-Wire Insulated ...assembly process flow, with minimal capital ... Fine Pitch Copper Wire... 8页 免费 Wire ...
热门文档