选填,简要介绍文档的主要内容,方便文档被更多人浏览和下载。
非稳态。计算时总是出现divergence detected in AMG solver:pressure correction。收敛因子已经调小,请求高手指点。万分感谢!
如果你的网格质量没有问题( The skewness must be less than 0.85 for Quad/Hex and 0.9 for Tri/Tet cells),那就可能是压力速度耦合方式的问题,你也可以检查下你的压力插值格式是否适合多相流计算;也有可能是边界条件设置的问题。
下面是doc.guandang.net论坛上的回答,我觉得讲的挺有条理的,这个是可压缩计算出现这个警告的解决回答,你看看对你有用的方面就行了。
Well, this message shows that the run is diverging, namely in pressure correction
equation (Sec. 25.4.3 Pressure-Velocity Coupling of Fluent Users Guide). It's hard to tell why this is happening without checking your case.
Are you following some of the solution convergence steps mentioned in this page?- Other suggestions I can make -
(1) What pressure-velocity coupling scheme are you using? I found that switching to PISO and turning on skewness correction sometimes helps on skewed meshes.
(2) What's the under relaxation factor for temperature (energy)? I find it helpful to reduce it to 0.8-0.9 in problems involving high-speed compressible flows.
A coupled of other thing that comes to mind:
(3) FMG initialization may help (Sec. 25.15 Full Multigrid (FMG) Initialization).
(4) Precision issue. What is the minimum cell volume (Grid - Check)? If it's less than 1e-06, then double-precision solver is recommended.
density based适用于可压缩流,
pressure based适用于不可压缩流.Z8M
density based把density作为主要变量之一。但不可压时density是常数(一般加入假想的人工可压缩性,来减缓这个矛盾)]
一般来讲,Pressure-Based Solver是Fluent的优势,它是基于压力法的求解器,使用的是压力修正算法,求解的控制方程是标量形式的,擅长求解不可压缩流动,对于可压流动也可以求解;Fluent 6.3以前的版本求解器,只有Segregated Solver和Coupled Solver,其实也就是Pressure-Based Solver的两种处理方法;
Density-Based Solver应该是Fluent 6.3新发展出来的,它是基于密度法的求解器,求解的控制方程是矢量形式的,主要离散格式有Roe,AUSM+,该方法的初衷是让Fluent具有比较好的求解可压缩流动能力,但目前格式没有添加任何限制器,因此还不太完善;它只有Coupled的算法;对于低速问题,他们是使用Preconditioning方法来处理,使之也能够计算低速问题。
你说的Density-Based Solver下肯定是没有SIMPLEC,PISO这些选项的,因为这些都是压力修正算法,不会在这种类型的求解器中出现的;建议你还是使用Pressure-Based Solver解决你的问题。
在你启动Fluent的时候不就有个2d,2ddp,3d,3ddp的选项吗?2ddp就是双精度的。
8-31-rke-steady-4-0.8 运行至 11000 迭代步是报错“divergence detected in AMG solver: pressure correction”(补充:每个工况均遇到此类情况,原因尚未找到,...
出现时机 Error: divergence detected in AMG solver Error: Object: () / ...I had a similar problem, but with pressure correction. I found that I ...
fluent常见错误_能源/化工_工程科技_专业资料。http...Reverse flow in XX faces on pressure-outlet-X ...divergence detected in AMG solver.# G- ]6 o0...
fluent例子_计算机软件及应用_IT/计算机_专业资料。...11 1451 reversed flow in 8 faces on pressure-...Error: divergence detected in AMG solver: w-...
when the fluent is divergence,the velocity or pressure is very large,and give: Error: divergence detected in AMG solver: pressure correction Error Object:...
fluent例子_计算机软件及应用_IT/计算机_专业资料。...11 1451 reversed flow in 8 faces on pressure-...Error: divergence detected in AMG solver: w-...
热门文档