表面活性剂在油田的应用
640 Manish M Kulkarni et al
sumes a nearly spherical shape (contact angle, θ 140°). Contact angle at the three phase contact line of heptane–water–quartz (which is considered to be almost non-porous) was observed to be ~20°. So it can be concluded from these observations that the higher contact angle for the heptane–water–silica film system is possibly because of: (i) the presence of partially hydrophobic unreacted –OC2H5 groups from the TEOS precursor on the surface of silica equilibrium contact angle. These results show that the change in contact angle is primarily because of diffusion of surfactant from sub-phase to drop, and is a function of surfactant concentration.
To verify that surfactant diffusion takes place from sub-phase to the droplet and vice versa (i.e. a re-versible two-way process), next, the sub-phase with CTAB concentration of 5 times CMC was further

clusters and (ii) the heptane–water interfacial energy being dominant than that of the water drop and the silica surface. The distribution of heptane and water in the pores of the film is complex, but from the higher contact angle of water drop on the oil side surface of the film, it seems that heptane phase dominates in the pores.
Wetting of the silica film by a water droplet can be controlled either by changing the roughness or the chemical property of the film, or, as shown in the present studies, by allowing diffusion of a sur-factant across the oil–water drop interface. Since the silica film is porous and there is a concentration gradient, surfactant diffuses from sub-phase to the water drop or vice versa. In this regard, we have studied the effect of two different water soluble sur-factants, namely, cetyl trimethyl ammonium bro-mide (CTAB), and sodium dodecyl sulfate (SDS), which are cationic and anionic, respectively.
Contact angle of the heptane–water–silica film system with pure water as the sub-phase is 140o, as shown in figure 3a. This sub-phase was exchanged with five times the critical micellar concentration (CMC) of CTAB, without disturbing the water drop-let or the silica film. As a result, CTAB diffused from the sub-phase to the droplet and the contact angle decreased to 16° within 25 min (figure 3b). We found that the rate of change of contact angle was almost constant with time, and once the surfac-tant concentration in the drop became equal to that in the sub-phase, the contact angle stabilized to 16°. From table 1, the experimentally measured value of pure water–heptane interfacial tension is 49 mN/m. With increase in CTAB concentration from 0 1 to 10 times CMC, this interfacial tension decreased from 25 to 1 mN/m. Therefore, with diffusion of CTAB into the droplet, θ decreased significantly due to the adsorption of CTAB at the oil–water droplet inter-face. As expected, the rate of change of contact angle increased with increase in sub-phase surfactant con-centration. As shown in table 2, this rate increased to 6 deg/min, on increasing CTAB concentration to 5 times CMC, with simultaneous decrease in final
Figure 3. Photographs showing surfactant mediated partial reversible switching of the wetting properties of a porous silica film grown and stabilized at the heptane–water interface. The transitions depicted are hydrophobic to hydrophilic and then back to hydrophobic again. (a) Water drop placed on heptane-side of the silica film with 5 CMC CTAB concentration in the aqueous sub-phase, at the instant t = 0, with contact angle, θ = 140°, (b) after t = 25 min, θ = 16° and (c) after replacing the sub-phase back with pure water, θ increases again to 90° after 2 h.
Synergism in the wetting properties of ternary surfactant mixtures 隐藏>> Synergism in the Wetting Properties of Ternary Surfactant Mixtures Hermann G. Hauth...
ed Surfactants and Wetting: IV. Spreading Behaviour of Trisiloxane Surfactants...lm 0.3 nm thick.5 Fast adsorption of surfactant molecules onto the sub...
ed Surfactants and Wetting: IV. Spreading Behaviour of Trisiloxane Surfactants...lm 0.3 nm thick.5 Fast adsorption of surfactant molecules onto the sub...
热门文档