文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 能源/化工 > surfactant controlled switching of water-in-oil wetting behaviour of porous silica films grown at oi
侵权投诉

surfactant controlled switching of water-in-oil wetting behaviour of porous silica films grown at oi

表面活性剂在油田的应用

Sub-phase controlled wetting of porous silica films 639

ting properties of such porous films by changing the surfactant concentration of the sub-phase while keeping the film straddled at the oil–water interface. lyst (NH4OH), TEOS reacts with water to form a random porous network of silica (in the form of a film) at the oil–water interface. We study the wet-

surfactant controlled switching of water-in-oil wetting behaviour of porous silica films grown at oi

Figure 2. SEM microstructure of silica films synthe-sized at heptane–water interface using 1 M NH) without any surfactant in the sub-phase, (4OH sub-phase: (ab) 1 CMC CTAB sub-phase and (c) 1 CMC SDS sub-phase (scale bar represents 5 μm).

Figure 1 shows a schematic diagram of our experi-mental set-up.

The silica films synthesized at the oil–water inter-face are composed of silica clusters connected to each other forming a network structure as shown in figure 2. Figure 2a shows the microstructure of the silica film prepared using 1 M NH4OH in the sub-phase without any surfactant. Surface of such a film shows a network of hierarchical 0 3–2 μm silica clusters with a prominent bimodal size distribution. Macroscopically, the film was relatively smooth. Addition of surfactants to the 1 M ammonia sub-phase before the formation of silica films affected the growth and microstructural properties of the sil-ica film. SEM micrograph in figure 2b shows that addition of CTAB at around its CMC to the sub-phase led to the formation of silica films displaying prominently only the large clusters (~ 2 μm). The smaller features visible in figure 2a are absent. In contrast, the silica films prepared with SDS sub-phase show much smaller clusters (~ 200 nm) and tighter pores (figure 2c). Also, in the case of CTAB surfactant sub-phase, the growth rate of the silica film was very fast and 1–2 mm thick films were ob-tained in ~30 min, whereas very thin films were ob-tained in the case of SDS even after 24 h. In fact, the silica film prepared using SDS was very brittle and often developed cracks even under the weight of a water drop placed on it. As a result, contact angle measurements could not be performed on these films. Whereas, in the case of CTAB sub-phase, the silica films were very thick, rough and the oil side surface often wrinkled, which obstructed the visibil-ity of water drop-silica film contact line so accurate measurements of the contact angle on these films also could not be performed. In view of the above factors, the films grown without surfactants were found to be most suitable for the contact angle measurements reported below.

Wetting properties of the film were studied by the three phase contact angle measurements in which a silica film straddling at the oil–water interface was used as a substrate. Water completely wets the dried silica film in air although some unreacted hydropho-bic –OC because when exposed to moist air, Si–OC2H5 groups might be present on the film sur-face172H5

hydrolyse quickly and the film looses its hydro-phobicity.20

However, it has been observed that in

the presence of heptane, a pure water droplet as-

上一页第3页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email