JESD
JEDEC Standard No. 22-A100-B
Page 4
4 Test Conditions (cont’d)
4.2 Biasing guidelines (cont’d)
4.2.3 Choosing and reporting – criteria for choosing continuous or cyclical bias, and whether or not toreport the amount by which the die temperature exceeds the chamber ambient temperature, aresummarized in Table 1:Table 1 — Cyclical Bias and Reporting Tja
Cyclical Bias?Report Tja? Tja
NoNo Tja < 5 °C, orPower per DUT < 200 mW
NoYes( Tja 5 °C, or
Power per DUT 200 mW)
and Tja < 10 °C
YesYes Tja 10 °C
5 Procedures
The test devices shall be mounted in a manner that exposes them to the specified temperature and
humidity with a specified electrical biasing condition. The test devices shall be placed in the test chamberwith the sample and chamber at room ambient temperature and humidity. Care shall be taken to minimizethe occurrence of condensation on devices and electrical fixtures.
5.1 Ramp-up and ramp-down
During ramp-up and ramp-down, condensation shall be avoided by ensuring that the test chamber (drybulb) temperature exceeds the wet bulb temperature at all times. The rate of temperature change shall notexceed
10 °C/minute. At all interim and final endpoint measurements, the chamber humidity and temperatureshall be reduced to room ambient conditions before removing the devices from the chamber.
5.2 Transition periods
During the transition periods from 65 °C to 30 °C and back up to 65 °C, the relative humidity may drop aslow as 80%. The chamber shall be vented to avoid artificial pressurization.
5.3 Test clock
The test clock starts at the beginning of the initial ramp-up and stops at the end of the final ramp-down.
5.4 Bias
Bias shall be verified after devices are loaded, prior to the start of the test clock. Bias shall also be verifiedafter the test clock stops, but before the devices are removed from the chamber.
Test Method A100-B
(Revision of A-100-A)
JEDEC STANDARD Cycled Temperature-Humidity-Bias Life Test JESD22-A100D (Revision of JESD22-A100-C,October 2007) JULY 2013 JEDEC SOLID STATE TECHNOLOGY ...
JEDEC 工业标准 环境应力试验 [JDa1] JESD22-A100-B Cycled Temperature-Humidity-Bias Life Test 上电温湿度循环寿命试验, (Revision of JESD22-A100-A) ...
Samples are subjected to a non-condensing, humid atmosphere, similar to the JESD-22-A101, "Steady State Temperature, Humidity and Bias Life Test", but...
JEDEC 工业标准 环境应力试验 [JDa1] JESD22-A100-B Cycled Temperature-Humidity-Bias Life Test 上电温湿度循环寿命试验, (Revi...
JEDEC STANDARD Cycled Temperature-Humidity-Bias Life Test JESD22-A100C (Revision of JESD22-A100-B, April 2000) OCTOBER 2007 JEDEC SOLID STATE TECHNOLOGY ...
(High/ Low Temperature Operating Life)目的: 评估...JESD22-A113-D EIAJED- 4701-B101 评估结果:八...(Temperature Humidity Bias Test)目的: 评估 IC ...
humidity (autoclave), extreme hot and cold ...life testing as a DC biased elevated temperature ...JESD22-A110B -40°C to +85°C Cycled bias (...
humidity (autoclave), extreme hot and cold ...life testing as a DC biased elevated temperature ...JESD22-A110B -40°C to +85°C Cycled bias (...
humidity (autoclave), extreme hot and cold ...life testing as a DC biased elevated temperature ...JESD22-A110B -40°C to +85°C Cycled bias (...
B Bias Current Source Test Condition Temperature :...a period (2) Vibration time : period cycled ...Humidity resistance Inductance change : Within ± ...
热门文档