文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > JESD22-A100-B_2000_Cycled_Temperature-Humidity-Bias_Life_Test
侵权投诉

JESD22-A100-B_2000_Cycled_Temperature-Humidity-Bias_Life_Test

JESD

JEDEC Standard No. 22-A100-B

Page 3

4 Test Conditions (cont’d)

4.2 Biasing guidelines

4.2.1 Apply bias according to the following guidelines:

a) Minimize power dissipation.

b) Alternate pin bias as much as possible.

c) Distribute potential differences across chip metallization as much as possible.

d) Maximize voltage within operating range.

NOTE — The priority of the above guidelines depends on the mechanism and specific device

characteristics.

4.2.2 Either of two kinds of bias may be used to satisfy these guidelines, whichever is more severe:

a)Continuous bias – the dc bias shall be applied continuously. Continuous bias is more severe than

cycled bias when the die temperature is less than or equal to 10 °C higher than the chamber

ambient temperature, or if the die temperature is not known when the heat dissipation of the

device under test (DUT) is less than 200 mW. If the heat dissipation of the DUT exceeds 200

mW, then the die temperature should be calculated. If the die temperature exceeds the chamberambient temperature by more than 5 °C, then the die temperature rise above the chamber ambientshould be included in reports of test results since the acceleration of failure mechanisms will beaffected.

b)Cycled bias – the dc voltage applied to the devices under test shall be periodically interrupted

with an appropriate frequency and duty cycle. If the biasing configuration results in a temperaturerise above the chamber ambient , Tja, exceeding 10 °C, then cycled bias, when optimized for aspecific device type, will be more severe than continuous bias. Heating as a result of power

dissipation tends to drive moisture away from the die and thereby hinders moisture-related failuremechanisms. Cycled bias permits moisture collection on the die during the off periods when thedevice power dissipation does not occur. Cycling the DUT bias with one hour on and one hour offis optimal for most plastic encapsulated microcircuits. The die temperature, as calculated on thebasis of the known thermal impedance and dissipation, should be quoted with the results

whenever it exceeds the chamber ambient by 5 °C or more.

Test Method A100-B

(Revision of A-100-A)

上一页第7页

你可能喜欢

热门文档

相关文档

  • JESD22-A100D-Cycled Temperature-Humidity-Bias Life ...

    JEDEC STANDARD Cycled Temperature-Humidity-Bias Life Test JESD22-A100D (Revision of JESD22-A100-C,October 2007) JULY 2013 JEDEC SOLID STATE TECHNOLOGY ...

  • JEDEC标准族

    JEDEC 工业标准 环境应力试验 [JDa1] JESD22-A100-B Cycled Temperature-Humidity-Bias Life Test 上电温湿度循环寿命试验, (Revision of JESD22-A100-A) ...

  • JESD22-A118

    Samples are subjected to a non-condensing, humid atmosphere, similar to the JESD-22-A101, "Steady State Temperature, Humidity and Bias Life Test", but...

  • JEDEC工业标准

    JEDEC 工业标准 环境应力试验 [JDa1] JESD22-A100-B Cycled Temperature-Humidity-Bias Life Test 上电温湿度循环寿命试验, (Revi...

  • JEDEC 100系列标准

    JEDEC STANDARD Cycled Temperature-Humidity-Bias Life Test JESD22-A100C (Revision of JESD22-A100-B, April 2000) OCTOBER 2007 JEDEC SOLID STATE TECHNOLOGY ...

  • IC可靠性测试项目及参考标准

    (High/ Low Temperature Operating Life)目的: 评估...JESD22-A113-D EIAJED- 4701-B101 评估结果:八...(Temperature Humidity Bias Test)目的: 评估 IC ...

  • SRF-1016Z中文资料

    humidity (autoclave), extreme hot and cold ...life testing as a DC biased elevated temperature ...JESD22-A110B -40°C to +85°C Cycled bias (...

  • SRF-2016Z中文资料

    humidity (autoclave), extreme hot and cold ...life testing as a DC biased elevated temperature ...JESD22-A110B -40°C to +85°C Cycled bias (...

  • SRQ-2116Z中文资料

    humidity (autoclave), extreme hot and cold ...life testing as a DC biased elevated temperature ...JESD22-A110B -40°C to +85°C Cycled bias (...

  • PCMC135T-1R0MF中文资料

    B Bias Current Source Test Condition Temperature :...a period (2) Vibration time : period cycled ...Humidity resistance Inductance change : Within ± ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email