文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 建筑/土木 > WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书
侵权投诉

WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书

无垃圾及油污,周围的沟道已回填完。

Foundation strength more than 70%, surface scabbled and free from rebar exposed,

honeycomb, crack, loosen, waste and oil sludge, and surrounding trench

backfilled.

根据图纸在地脚螺栓两侧及承力处,用墨汁画出垫铁摆放位置。

To mark pack location on the sides of bolts and bearing as per drawing.

根据垫铁画线,将摆放垫铁的基础用基础锤凿平,用红丹粉检查垫铁与基础水泥面

接触面积大于75%。

To mark as pack and chisel flat, to check for contact area of shim with foundation more than

75% by red lead. 垫铁表面经机加工,表面平整,无翘曲和毛刺,垫铁的坡度一般为1:10~1:25,

且薄边厚度不小于5mm。

Pack shall be machined, and the surface shall be flat and free from burrs and warp. The slope

to be 1:10~1:25 with thin edge not less than 5mm thick.

在放置垫铁位置的基础上,用水准仪测量基础标高值,此值与设备底座标高相比较,

所得数值为此处垫铁的安装高度。根据计算的垫铁高度,选取垫铁的合理配置,垫

铁布置一般不超过3块,特殊情况下允许5块,其中斜垫铁允许1对,并比底座边

宽出10~20mm。斜垫铁错开面积不大于垫铁面积的25%,并且斜垫铁的斜度为1:

10~1:25,一组垫铁的厚度为50~60mm。

To survey the elevation of foundation where pack to be placed and it to be compared with

bottom elevation of equipment, the difference to be the installation height of pack. To select

proper packs according to the height, and generally the number of packs not more than 3

pieces, in special situation 5 pieces allowed, in which one pair of slope packs allowed and

10~20mm wider than base edge.

将润滑油站用30t运输车运至汽机房,运输过程中应用链条葫芦封好车。

To carry LO station to ST building by 30t truck.

润滑油站运至汽机房后,选用一对φ32.5长22米的钢丝绳用汽机房行车通过

+17.950米层及+11.950米层预留的空间区域将润滑油站吊放在设备基础上。吊装过

WI-8710-8100-0099, Rev.B page 8 of 19

上一页第8页

你可能喜欢

  • 汽轮机检修
  • 背压式汽轮机
  • 汽轮机轴承
  • 汽轮机发电
  • 施工现场安全管理制度
  • 汽轮机安装
  • 管道安装施工方案

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email