文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 建筑/土木 > WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书
侵权投诉

WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书

fixed properly and 2~3 threads to be exposed.

油系统管道未全部安装接通时,对油管敞口部分应临时封闭。

The opening of oil piping shall be temporary closed during installation. 对汽轮发电机需隔绝电流的各部分与油管连接时,应注意加装必要的绝缘件,组装

前应检查绝缘件完好无损,并应安装正确。

Proper insulation component shall be fixed correctly, while all parts of ST generator, which need to be insulated, being connected to oil piping.

9.2.2汽机控制油管道及顶轴油管道安装:installation of ST control oil and jacking oil piping

控制油管道及顶轴油管道为不锈钢管道,安装前进行内部清理,已经过内部清理后的管道及时封口并单独存放,保持内部清洁干燥,管道下料采用专用工具切割,弯管采用冷弯工艺,管道的吊运存放严格按不锈钢管材的存放、保管要求进行,焊接采用氩弧焊。

These are stainless steel piping, which is to be inner cleaned and pipe ends to be closed to keep inner dry and clean. Special cutting tools shall be applied, bends apply cold bending, storage and handling of pipes be carried out properly, and argon welding to be applied.

9.2.2.1系统安装特点:installation points

DN50以上的管道弯头一般采用机制弯头;DN50(包括DN50)以下的管道弯头一般需现

场弯制,弯制时必须采用冷弯,不得加热,并且要保证设计弯管半径;三通、大小头等管件全部为机制;管线上一般不设法兰、阀门等;管道之间对口连接一般采用套管焊接,套管的长度要符合设计要求;管道支吊架一般采用木制或硬塑料机制支吊架。

Machine-made bends apply for pipe DN50 above, and site-made cold bends for DN50 below. All T-pieces and reducers ect. shall be machine-made. Generally no flanges and valves in the piping, and welding spools compliant to design requirement shall be applied for connections. Wooden or hard plastic machine made supports and hangers to be applied.

WI-8710-8100-0099, Rev.B page 14 of 19

上一页第14页

你可能喜欢

  • 汽轮机检修
  • 背压式汽轮机
  • 汽轮机轴承
  • 汽轮机发电
  • 施工现场安全管理制度
  • 汽轮机安装
  • 管道安装施工方案

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email