文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 建筑/土木 > WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书
侵权投诉

WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书

有条件的以30/1000~50/1000为好。

Feeding piping shall have a slope of 1/1000 to pump side, and return piping has a slope of 5/1000 above to tank side, 30/1000~50/1000 preferred.

油管与基础、设备、管道或其他设施应留有膨胀间隙,保证运行时不妨碍汽轮机和

油管自身的热膨胀;与膨胀较大的设备部件或管道连接的小油管应考虑膨胀补偿。 Expansion joint shall be remained between piping and foundation/equipment/other piping or facilities to prevent from obstructing ST running and heat expansion of itself, and expansion compensation shall be considered for small piping connected with equipment with much expansion or piping.

油管外壁与蒸汽管保温层外表面一般应保持不小于150mm的净距,距离太小时应加

隔热板,对于运行中经常存有静止油的油管,应加大距离,在主蒸汽管道附近的油管,不宜设置法兰。

At least 150mm space shall be kept between piping and outer surface of Steam pipe insulation,

管子和阀门的荷重应由支吊架承受,一般不得承受在设备上或油管接头上。

Piping and valves shall be supported by supports and hangers, while not being on the equipment or joints of piping.

油管道的法兰结合面应使用质密耐油并耐热的垫料,不得使用塑料或胶皮垫。垫片

应清洁、平整、无折痕,其内径应比法兰内径大2~3mm,外缘应与法兰螺栓内缘相接。

Compact, oil-proof and heat resistant gasket shall be applied for flanged joint, instead of plastic or rubber ones. Gaskets shall be clean and flat, without fold. Its inner diameter shall be 2~3mm more than that of flange.

油管道的法兰结合面与垫片,宜使用密封胶作涂料,涂抹应匀薄,不使挤入管口内。

油管法兰连接应无偏斜,不得强力对口,法兰螺栓必须对称地均匀紧固,并使露出2~3丝扣。

The contact surface and gasket shall apply sealing glue evenly without squeezing into pipe, and flanges shall be no deviation and under force. Bolts shall be

WI-8710-8100-0099, Rev.B page 13 of 19

上一页第13页

你可能喜欢

  • 汽轮机检修
  • 背压式汽轮机
  • 汽轮机轴承
  • 汽轮机发电
  • 施工现场安全管理制度
  • 汽轮机安装
  • 管道安装施工方案

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email