文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 建筑/土木 > WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书
侵权投诉

WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书

valve is not allowed. Valve stem shall be level or downward to prevent valve butterfly drop off and block piping. Emergency drain valve shall adopt two gate valves in series.

所有支吊架的安装均应符合设计要求且牢固可靠,滑动及导向支吊架的活动面应清

洁并活动自如;对未出布置图的支吊架,要求以不妨碍其它管道及设备并布置合理牢固为宜。

All supports and hangers shall be installed compliant to design requirement and firm and reliable. Slide and guiding supports and hangers could be moved smoothly.

对于不锈钢油管部分安装,其安装方法同普通碳钢油管道安装,其不同之处在于下

料不得用火焊、无齿锯、磨光机,必须用管子割刀;焊接需全氩焊接。

For stainless steel piping, it’s to be installed same as that of carbon steel piping with exception of no use of fire welding, toothless saw and grinder. Tube cutting knife shall be used and full-argon welding be applied.

9.2.1.3汽机油系统管道安装应符合下列条件:the following conditions shall be met:

油管法兰面的密封面均应平整光洁,接触均匀并不得有贯通密封面内外缘的沟痕,

接触不良时应进行机加工或修刮。

Flange contact surface shall be smooth and clean, and free from groove or dent run through surface. Machining shall be done if bad contact found.

油管道应尽量减少法兰接口和中间接口,除与设备连接必需外,一般不采用活接头

连接,并确保油管内清洁,管子焊接前必须经施工负责人检查内部已彻底清理干净,才允许施焊,焊接应采用氩弧焊打底,DN50以下油管应采用全氩焊接。

Flanged joints/intermediate joints shall be minimized as much as possible. Union joints not to be used except for connection with equipment. Inside of pipes shall be cleaned before welding. The argon welding for root shall be applied, and full-argon welding for DN50 below.

进油管应向油泵侧有1/1000的坡度,回油管应向油箱侧倾斜,坡度不小于5/1000,

WI-8710-8100-0099, Rev.B page 12 of 19

上一页第12页

你可能喜欢

  • 汽轮机检修
  • 背压式汽轮机
  • 汽轮机轴承
  • 汽轮机发电
  • 施工现场安全管理制度
  • 汽轮机安装
  • 管道安装施工方案

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email