文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 建筑/土木 > WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书
侵权投诉

WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书

9.2油管安装:汽机油系统管道材料供货为半成品即预制状态供货的,不需进行酸洗工作。油系统管道安装施工工序和工艺如下:

oil piping installation: it’s delivered with semi-products, with no need of acid flushing. To be installed as following procedure:

9.2.1润滑油管道安装LO piping installation

9.2.1.1管道安装前应具备以下条件: pre-conditions:

与管道有关的土建工程经检查合格,满足安装要求;

related civil work inspected and acceptable.

与管道连接的设备找正合格,固定完毕;

equipment connected with equipment to be aligned and fixed.

管道、管件及阀门等已经检验合格,按设计要求核对无误,内部已清理干净无杂物,

封头无脱落。

Pipes, fittings and valves inspected and acceptable.

9.2.1.2管道安装:piping installation

普通油管道的安装亦遵循一般中低压管道安装的基本步骤,根据图纸下料,磨口、

对口,地面组装后架空,根据图纸就位接口,复查坐标、尺寸,安装支吊架。

Conventional oil piping also adopts the installation procedure for normal MP/LP piping, ie. to cut as per drawings, grind, alignment, assembly, join as per drawing, check coordinate and dimension and install supports and hangers. 大口径管( DN50以上)的弯头应用热压弯头,DN50以下的弯头采用冷弯管;DN25

以下(含DN25)的三通采用机制三通,DN50(含DN50)以上的三通无设计或特殊规定可现场配制,但必须认真清理焊渣、焊瘤、药皮等杂物。

Hot press bends apply for large caliber pipe (DN50 above), and cold bends for DN50 below. Machine-made T-pieces for DN25 and below, and site-made for DN50 and above which shall free from slag, overlap etc.

阀门安装要有明确的开关方向标志,应采用明杆阀门,不得采用反向阀门;阀门杆

应平放或向下防止运行中阀蝶脱落切断油路;事故排油阀应设两个闸阀串联。 Valve shall adopt clear stem and be installed with clear switch mark, and reverse

WI-8710-8100-0099, Rev.B page 11 of 19

上一页第11页

你可能喜欢

  • 汽轮机检修
  • 背压式汽轮机
  • 汽轮机轴承
  • 汽轮机发电
  • 施工现场安全管理制度
  • 汽轮机安装
  • 管道安装施工方案

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email