文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 建筑/土木 > WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书
侵权投诉

WI-8710-8100-0099 Rev.B 汽机油系统设备及管道安装作业指导书

not touch the hole wall. To tighten bolts after the strength of grouting up to 70% that of design and above.

9.1.2油泵对轮找正 pump coupling alignment

以泵为基准,进行联轴器找中心。

Base on pump, to carry out alignment of coupling.

泵与电机间有联轴节的找正:联轴器找中心采用四点对中法,即在周围方向上,在

互成90º的位置分别标记为0º、90º、180º、270º,用一块百分表测圆周,两块百分表测端面,其误差值及预留偏差要符合厂家要求或《验标》中的《机7—1—6》。 Alignment of pump and motor with coupling: 4-point alignment to be applied, that is to mark 0º, 90º, 180ºand 270º in girth of coupling and measure girth with one dial indicator and measure end face with two dial meters, the error and preset deviation shall comply with manufacturer’s requirement or “inspection criteria—machine 7—1—6”.

泵与电机间无联轴节的找正:联轴器找中心时,应使两联轴器间保持一定的距离,

其值要大于泵与电机轴向窜动的总和,以防止泵与电机各自产生轴向窜动时的相互碰撞。由于联轴器间距有限,不能使用百分表,可用塞尺来测量端面偏差。圆周方向仍用百分表来测量偏差。在用塞尺测量时,每次塞尺插入的深度及使用的力量都力求相同,塞尺塞入时的力量不要过大,以防卡子走动,引起误差。其预留偏差和误差值均要符合厂家要求或《验标》中的《机7—1—6》。

Alignment between pump and motor without coupling: the two couplings shall keep a distance more than sum drunkenness of pump and motor shaft to avoid mutual collide. Feeler is to be used to measure end’s deviation instead of dial indicator. Radial deviation to be measured with diameter. The depth and force for inserting feeler each time shall be identical. Its remained deviation and error shall meet manufacturer’s requirement or “inspection criteria—machine 7—1—6”.

联轴器连接coupling connection

泵与电机的联轴器通常采用销式螺栓连接,当螺栓拧紧后,全部螺栓均应受力并不得有卡位现象。

Pin-bolt to be applied for connection of coupling between pump and motor.

WI-8710-8100-0099, Rev.B page 10 of 19

上一页第10页

你可能喜欢

  • 汽轮机检修
  • 背压式汽轮机
  • 汽轮机轴承
  • 汽轮机发电
  • 施工现场安全管理制度
  • 汽轮机安装
  • 管道安装施工方案

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email