Particle dynamics in aeolian saltation has been studied in a boundary layer wind tunnel above beds composed of quartz grains having diameters of either 254 μm or 320 μm. The cross section of the tunnel is 600 mm × 900 mm and its thick boundary layer all
transit times (Rasmussen and Sørensen, 2005). Obviously such artefacts will influence the tails of the distribution of grain speed, but since they are not extremely small, they are unlikely to bias the calculated average grain speeds much.
Another cause for concern is the existence of temporal variation of transport characteristics caused by turbulent fluctuation of the wind speed, in particular influences induced by secondary flow because of the rectangular cross section of the tunnel. However, the dimension of the tunnel limit the creation of very large eddies, and for the speeds used in this study an air parcel will typically travel through the tunnel within 3-5 s. The influence from temporal variation at 40 mm height above the 242 µm bed is illustrated by plotting (Fig. 3) the average grain velocity and flux density as a function of the number of validated grains found in each run (as a measure of the duration of the run). The duration of the runs varies from 30 s to 400 s. All runs were made under identical conditions except that a small change in the set-up caused an increase in the average speed between run 1-8 and run 9-30. The scatter of the average grain speed is about 0.5 m/s for runs with less than 1000 grains whereas it is only about half of that value when the number of grains is somewhat larger than 1000 grains. The scatter in grain flux density seems to be around 2-4×106 grains s-1 m-2 for the short runs with few grains, but it also decreases to about half or less that value when the number of grains considerably exceeds 1000 grains. Thus averages tend to stabilize as the sampling time increases, indicating temporal stability of the wind tunnel. Variation of grain speed in the saltation layer
Grain speed is rarely measured in neither field nor laboratory experiments. However, in the present investigation we have measured profiles of the average horizontal grain speed (Vg) for grains above a 242 µm for four friction speeds (Fig. 4a), and for a 320 µm bed for 3 friction speeds (Fig. 4b). The data represent conditions in different parts of the saltation layer. Thus data recorded in the interval 5-10 mm above the bed represents the intense part of the saltation layer; those in the interval 15-20 mm are a bit above its most vigorous part, while those above 40 mm are in the upper part of the saltation layer where the grain concentration is low. The data for the lowest friction speed u*=0.272 m/s represents conditions not far above the saltation threshold, while the data for the higher values represent conditions at vigorous (u*=0.394 and 0.558 m/s) and intense transport (u*=0.685 m/s). It is interesting to see that all profiles converge towards a particle speed of about 1.3 m/s at 2-3 mm height above the bed. Like wind profiles (Bagnold 1941), grain speed profiles seem to have a focus point. The profiles increase smoothly with
height except for the 0.556 m/s profile which is based on fewer measurements and therefore also expected to show more scatter. The ratio between measured air and grain speed is about 1.2 for all friction speeds at the highest elevation of 80 mm (Fig. 5). Below 80 mm the ratio gradually increases to about 2 or slightly more at 5 mm height. Close to the bed there is considerable
scatter. This is to be expected because both wind speed and grain speeds are less well determined here. Moreover, because of the passing ripples, the height is also less well determined here so that the wind and grain speed measurements may have been made at slightly different heights. For the two particle sizes used here, there is no apparent influence from grain size in the ratio between air and grain speed.
The probability distribution of the grain speed was calculated for each of the heights where measurements were made and for the different friction speeds and grain diameters using the saltation model. To do so the parameters, i.e. phi (the mass flux of grains from the bed into the
The vertical variation of particle speed and flux density in aeolian saltation measurement Particle dynamics in aeolian saltation has been studied in a ...
In addition, it was found that when taking the Magnus force into account,...(2008), Vertical variation of particle speed and flux density in aeolian ...
In addition, it was found that when taking the Magnus force into account,...(2008), Vertical variation of particle speed and flux density in aeolian ...
热门文档