文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > The vertical variation of particle speed and flux density in aeolian saltation measurement
侵权投诉

The vertical variation of particle speed and flux density in aeolian saltation measurement

Particle dynamics in aeolian saltation has been studied in a boundary layer wind tunnel above beds composed of quartz grains having diameters of either 254 μm or 320 μm. The cross section of the tunnel is 600 mm × 900 mm and its thick boundary layer all

4 RESULTS AND DISCUSSION

Wind speed

Before any grain data were collected the boundary layer in the tunnel was investigated by recording profiles of wind speed between 10 mm and 200 mm height. The profiles revealed a “slight wake” region around 140 mm, while between 20 mm and 80 mm they strictly followed the “law of the wall” (White, 1991). Although not always visible, below 20 mm wind profiles are expected to be influenced by shear stress partitioning between grains and fluid so that during moderate or high mass transport, low level air speeds deviate from the law of the wall (Owen 1964, Sørensen 1985, 2004; Anderson & Haff, 1991; McEvan & Willetts 1993). Therefore the wind profiles that were collected during the first part of the investigation were only sampled between 20 mm and 80 mm above the bed. However, during the second part of the investigation data were sampled both from lower levels and with smaller vertical increment. This not only increased precision of the estimated friction speeds, but also allowed a more detailed comparison of the measured/predicted air and grain speeds.

Air speed profiles obtained for the four friction speeds at which grain dynamics were studied above the 242 µm grain bed are presented in Figure 2. Firstly, it is noticed that between 20 mm and 80 mm the data follow a log-linear profile with little scatter. Secondly, the aerodynamic roughness length (y0) increases steadily from about 10-4 m at u*=0.27 m/s (i.e. just above the saltation threshold) to about 10-3 m at u*=0.69 m/s. The observed systematic increase in y0 with increasing friction speed corresponds well to predictions by Owen (1964) as well as observations by e.g. Raupach (1991), Rasmussen et al. (1996), and McKenna Neuman and Maljaars (1997). Thirdly, it is noticed that for the three higher friction speeds, the observed air speeds in the region 5-10 mm above the bed are systematically higher than values extrapolated to the same heights from the log-linear wind profile. This probably indicates shear stress partitioning.

Grain speed

Laser-Doppler measurements

In most industrial and environmental applications the laser-Doppler instrument is used to measure the velocity of particles which are considerably smaller than saltating quarts grains. Caution must therefore be exerted in the interpretation of the recorded data. Thus early in the experiment it was observed that the horizontal grain velocities recorded at any level contained a small fraction of negative velocities - even when the velocity of the airflow was large. At 40 mm height, for instance, several grains had velocities smaller than -6 m/s when the average air speed was just over 6 m/s. Although negative speeds may occur occasionally (Bagnold, 1941) it seems unphysical that such negative values will be found at relatively large distance above a soft sand bed. However, for the large sand particles it is likely that a grain will only partially penetrate the control volume of the laser beams or that particle spin or facets on grain surfaces may produce artefacts in the recorded signals. Therefore the recorded data are likely to contain some unrealistic large positive or negative speeds. This interpretation of the negative velocities as mainly erroneous is further supported by the fact that negative values are only recorded for those grains that spend the shortest time in the control volume, i.e. particles which have the lowest

上一页第6页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email