文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > The vertical variation of particle speed and flux density in aeolian saltation measurement
侵权投诉

The vertical variation of particle speed and flux density in aeolian saltation measurement

Particle dynamics in aeolian saltation has been studied in a boundary layer wind tunnel above beds composed of quartz grains having diameters of either 254 μm or 320 μm. The cross section of the tunnel is 600 mm × 900 mm and its thick boundary layer all

of ripples is negligible. Mostly 2000 to 3000 grain speed values were measured below 20 mm height; several hundreds were recorded at 20 mm and 40 mm, while only 20-100 grain speeds were recorded at higher elevations. Because analysis of the 320 µm data revealed rather large scatter, in particular in the recorded grain rates, multiple runs at the same friction speed were made during the second part of the experiment where the bed was covered by 242 µm grains. Thus more than 500 samples were mostly recorded at the uppermost level of 80 mm while from 500 to more than 10,000 measurements were recorded at lower levels. The processed data contains information about particle arrival and transit time, but only for those data where the particle speed was validated by the Dantec software.

3 MODELING GRAIN SPEED AND FLUX IN AEOLIAN SALTATION The model of the trajectories of saltating grains used in this paper is a standard model. It is a slight modification of the model used in Jensen & Sørensen (1986). As in most other recent models, lift forces on the grains and effects of turbulent fluctuations are ignored when the grain has left the bed. The magnitude of the influence of lift forces is relatively small, see McEwan & Willetts (1993), and turbulent eddies are mainly of relevance for grains smaller than 100 µm. All sand grains are assumed to be identical. In particular, they have the same shape, so that the drag on a grain is a function only of the relative speed between the grain and the air. The drag on a grain at the relative speed w is denoted by D(w). The grain mass is denoted by m. Thus the equations of motion are

=H(w)(U(y) x )x +g+H(w)y =0y

where x and y denote the horizontal and the vertical position of the grain, respectively, H(w) = D(w)/(mw), and U(y) is the mean wind speed at height y. The reciprocal of the quantity H(w) has the dimension of time and can be interpreted as the response time of a grain to changes in the wind speed. The wind profile is taken to be logarithmic with friction speed and roughness height as measured during the experiments. Following Bagnold (1936) and many others we calculate the drag D(w) as the drag on an aerodynamically equivalent sphere, i.e. a sphere with the same terminal velocity of fall in air as the grains. Bagnold found the diameter of this sphere to be 0.75 times the diameter of the sand grains. We use the Schiller & Nauman (1933) formula

c(R)=241+0.15R0.687 R()

for the drag coefficient of a sphere, where R = 0.75dis the Reynolds number with d denoting the grain diameter and ν the kinematic viscosity of air. This formula has excellent accuracy for Reynolds numbers up to about 700, which is sufficient for aeolian saltation. It follows that

13.5µH(w)=2dσ0.687 dw 1+0.123 ν

上一页第4页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email