文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > The vertical variation of particle speed and flux density in aeolian saltation measurement
侵权投诉

The vertical variation of particle speed and flux density in aeolian saltation measurement

Particle dynamics in aeolian saltation has been studied in a boundary layer wind tunnel above beds composed of quartz grains having diameters of either 254 μm or 320 μm. The cross section of the tunnel is 600 mm × 900 mm and its thick boundary layer all

be opened a thus provide easy access to the tunnel interior. A small bell mouth followed by turbulence spires and a 3 m long replaceable array of roughness blocks provides a turbulent boundary layer in fair equilibrium with the boundary layer induced by ongoing saltation in the main part of the working section. Thus it is possible to avoid the overshoot of saltation otherwise typical for wind tunnel studies (Shao, 1993). Except for the larger cross section, the tunnel is almost similar to that described by Rasmussen & Iversen (1993). Grains are being fed into the tunnel 1 m before the end of the roughness array and caught in a 4 m wide expansion (sand collector) before the axial fan at the end of the tunnel. The speed of the air-flow can be varied continuously between zero and approximately 20 m/s.

In the experiment presented here, the bed was covered by a 25 mm thick layer of uniform sand grains. During the first part of the study grains having diameter Dp = 320 µm were used while profiles of air and grain speeds together with grain flux densities were measured at three friction speeds. Then the bed was replaced by one composed of 242 µm grains, and a new set of speeds and flux densities were obtained for four friction speeds. While recording a set of speeds and grain fluxes the average mass transport was determined as the total mass of grains collected in the sand collector divided by the duration of the experiment and the effective tunnel width (550 mm). Thus the procedure is similar to the one used in earlier experiment on effective mass transport (Rasmussen and Iversen, 1999).

Air speed above the 320 µm bed was measured at 10, 20, 40, and 80 mm with a pitot-static tube connected to an electronic micro-manometer (Barocell with a 1.5 mm Hg high-resolution differential pressure cell). Above the 242 µm bed air speeds were recorded at 5, 10, 15, 20, 30, 40, 50, 60, 70, and 80 mm. However, in both cases measurements were made only after an equilibrium bed texture, i.e. a bed with a uniform pattern of wind ripples, had developed. The velocity profile was determined as the average of one set of data recorded before and one set recorded after a set of grain speeds and flux densities were measured. From data on the vertical profile of the horizontal wind speed (u) the bed shear stress can be calculated using the logarithmic wind law

u=u*y lnky0(1)

where u* is friction speed, y0 is aerodynamic roughness height, and k is von Karman’s constant.

Grain speed was measured with a 1-D integrated 632.8 nm laser-optics system (LDA) consisting of a Dantec Flowlite instrument with a Flow Velocity Analyzer (FVA) signal

processor. The LDA-probe is configured with a beam separation of 38 mm and focal length of 400 mm which, according to the technical manual, results in a measuring window having height 0.2 mm and width 4.22 mm. Validation of the signal was chosen at -2 dB in order to have a reasonable signal to noise ratio. The grain velocity component in the mean flow direction, i.e. parallel to the axis of the wind tunnel was recorded with the laser head placed outside the glass panes in the tunnel front wall, and at about 3 m upwind of the sand collector. During the first part of the study, where the bed was covered by 320 µm grains, the duration of a run typically lasted from 15-60 seconds. Runs were short for measurements made close to the bed. Here the grain flux is high so that many measurements can be obtained quickly. Moreover, the local height of the sensor relative to the bed may vary when ripples move, which necessitates short runs. Longer runs were made farther away from the bed where grain concentrations are small and the influence

上一页第3页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email