Particle dynamics in aeolian saltation has been studied in a boundary layer wind tunnel above beds composed of quartz grains having diameters of either 254 μm or 320 μm. The cross section of the tunnel is 600 mm × 900 mm and its thick boundary layer all
Height (mm)
0.5
1
2
3
4
8 Particle diameter - Dp=242 µm u* 0.274 (m/s) σ σp2/σ2 1.11 1.018 1.22 0.943 1.25 0.912 1.15 0.957 0.94
1.213 0.394 (m/s) σ σp2/σ2 - 1.18 0.983 1.25 0.968 1.33 0.932 1.19 1.008 1.08 1.056 0.558 (m/s) σ σp2/σ2 1.17 0.966 1.29 0.891 1.39 0.835 1.41 0.851 1.65 0.733 1.27 0.884 0.685 (m/s) σ σp2/σ2 1.17 1.128 1.42 0.937 1.59 0.836 1.65 0.83 1.69 0.781 1.61 0.714 0.27 (m/s) σ σp2/σ2 0.93 0.968 1.15 0.809 1.18 0.839 1.00 1.050 0.59 1.763 Dp=320 µm u* 0.47 (m/s) σ σp2/σ2 1.15 1.009 1.28 0.914 1.41 0.879 1.42 0.887 1.47 0.844 0.74 (m/s) σ σp2/σ2 1.27 1.126 1.49 0.960 1.65 0.915 1.77 0.842 1.50 0.933
Table 3. Observed standard errors (σ) and the ratio between predicted and observed standard
errors (σp/σ) for different friction speeds and two particle sizes.
Values of the observed standard deviations (σ) of the horizontal grain speed distribution and the ratio between predicted and observed standard deviations (σp/σ).are given in Table 3 for the two grains sizes. There is much scatter in the table, which is to be expected since standard deviations are less well determined than means and are much more sensitive to erroneous extreme
measurements (outliers) that we know are present. There is a clear tendency for the standard deviations to increase with the friction speed. Perhaps there is a tendency that the standard
deviations are largest at the middle heights (around 4 cm). The observed variation of the standard deviation with height is not well predicted by the model because the model values vary in a much more smooth way. However, it should be noted that for the majority of the observations the discrepancy between the predicted and measured variance is less than 15 %.
The observed probability distribution of the horizontal grain speed is presented for two heights and two friction speeds for the 242 µm grains in Figure 6 together with model
calculations of the same distribution. The examples plotted in Figure 6 were chosen to illustrate what happens at a high and a low wind speed and in a height with intense saltation and a height with relatively low grain concentration. Generally there is fair agreement between the observed and predicted distributions. For the low friction speed, the majority of grains have speeds between 1 and 3 m/s. While grains having speeds between -1.0 and 1.0 m/s are also quite
common at the low height, these grains are rarely found at 20 mm height where the second most common group are grains with speeds between 3 and 5 m/s. Grains in the range 1-3 m/s are also the most common group at 5 mm height for the high friction speed, but at 40 mm height these grains are rare and the velocity spectrum is dominated by grains having speeds in the wider range from 3 and 7 m/s. Qualitatively the observed variation agrees with the perception that during the
The vertical variation of particle speed and flux density in aeolian saltation measurement Particle dynamics in aeolian saltation has been studied in a ...
In addition, it was found that when taking the Magnus force into account,...(2008), Vertical variation of particle speed and flux density in aeolian ...
In addition, it was found that when taking the Magnus force into account,...(2008), Vertical variation of particle speed and flux density in aeolian ...
热门文档