Particle dynamics in aeolian saltation has been studied in a boundary layer wind tunnel above beds composed of quartz grains having diameters of either 254 μm or 320 μm. The cross section of the tunnel is 600 mm × 900 mm and its thick boundary layer all
splash only a limited number of grains will receive a large vertical momentum through the conversion of forward momentum of the impinging grain, while several grains will receive a
relatively small momentum and make low, short jumps. The few grains that jump as high as 40 or 80 mm are all accelerated during ascent by the increasing wind speed further away from the bed. As the friction speed increases, saltating grains will receive an increasing amount of forward momentum which will increase not only the chance that more grains will be set in motion by the collision of an impinging grain, but also the chance that the ejected grains will jump higher. The result is that the distribution near the bed is not changed much while the distribution far from the bed changes much more.
We believe that observation quite close to the bed poses a series of technical difficulties, so in the present experiment data were generally not recorded below 5 mm height. However, while the majority of grains have positive speeds at both 5 mm and higher a small proportion of the measured grain speeds are negative (i.e grains having ejection angle > 90°). Even though the model allows grains to start at an angle of 150° (i.e. 60° against the wind direction), it predicts that negative grain speeds are extremely unlikely even at 5 mm above the bed. As discussed above we therefore think that most of the measured negative grain speeds are erroneous and due to grain spin, grain facets and effects of the relatively large particle diameter. The issue has been further investigated by measuring the grain velocity distribution at 3 mm height above the bed composed of 242 µm grains. For a friction speed of 0.27 m/s only 2% of the grains were found to have a negative speed so that it is probably not a serious problem.
Previous experimental studies as well as numerical modelling indicate that immediately above the bed the speed of an impinging grain is typically in the range of 2-8 m/s (e.g. Willetts and McEwan, 1991; Anderson and Haff, 1991). Comparison of the data in Fig. 4 shows that the speeds we have measured at 5 mm height are within the range of expected speeds for an
impinging grain. Our data includes ejected grains too, so it is not surprising that our mean speeds are in the lower end of the interval. Experimental data on the variation of grain speed close to the bed are few, but in a recent study Dong et al. (2002) presents data on the distribution of impact speed for different grain sizes and free stream velocities. For the same particle sizes their study generally records impact speeds which are much lower than the bulk speeds found here -
typically an order of magnitude. Apart from the serious problems connected with measurements very close to the bed, the difference might partly be due to the fact that close to the bed the proportion of (slow) ejected grains is much larger than 5 mm from the bed. We take the
consistent behaviour of our measurements and model predictions combined with the fact that our experimental data are in fair agreement with observed particle trajectories (White & Schultz, 1976; Nalpanis, 1985) and numerical predictions (Anderson & Haff ,1991) as an indication that the grain speed data recorded with the laser-Doppler instrument are not severely influenced by particle spin, influence from large particle diameter, grain facets and other measurement errors which may significant influence results if not handled properly.
Grain flux density
Vertical profiles of mass transport are commonly recorded in aeolian research for estimation of the total sand transport by wind although this is difficult given the non-linearity of the profile and the vigorous nature of transport close to the bed (Butterfield, 1999; Butterfield, 1991; Rice et al. 1995, 1996). Vertical profiles are also commonly used for calibration of numerical saltation
The vertical variation of particle speed and flux density in aeolian saltation measurement Particle dynamics in aeolian saltation has been studied in a ...
In addition, it was found that when taking the Magnus force into account,...(2008), Vertical variation of particle speed and flux density in aeolian ...
In addition, it was found that when taking the Magnus force into account,...(2008), Vertical variation of particle speed and flux density in aeolian ...
热门文档