MAX3420 -usb资料
USB Peripheral Controller
with SPI Interface

MAX3420E
(NOVBUSIRQ)) and disconnect the internal 1.5kΩpullup resistor. If the device using the MAX3420E isbus powered (through a +3.3V regulator connected toVCC), the MAX3420E VBCOMP input can be used as ageneral-purpose input. Using VBCOMP as a general-purpose input requires a 10kΩ pullup resistor fromFigure 10. Behavior of the INT Pin for Different INTLEVEL andVBCOMP to VL. See the Applications Informationsec-POSINT Bit Settings
tion for more details about this connection.
D+ and D-RES
The internal USB full-speed transceiver is brought outDrive RESlow to put the MAX3420E into a chip reset. Ato the bidirectional data pins D+ and D-. These pins arechip reset sets all registers to their default states,±15kV ESD protected. Connect D+ and D- to a USBexcept for PINCTL (R17), USBCTL (R15), and SPI logic.“B” connector through 33Ω±1% series resistors. AAll FIFO contents are unknown during chip reset. Bringswitchable 1.5kΩpullup resistor is internally connectedthe MAX3420E out of chip reset by driving REShigh.to D+. According to the USB rev 2.0 specification, aThe RESpulse width can be as short as 200ns. See theself-powered peripheral must disconnect its 1.5kΩDevice Resetsection for a description of the resetspullup resistor to D+ in the event that the host turns offavailable on the MAX3420E.
bus power. The VBGATE bit in the USBCTL (R15) regis-ter provides the option for the MAX3420E internal logicINT
to automatically disconnect the 1.5kΩresistor on D+.The MAX3420E INT output pin signals when a USBThe VBGATE and CONNECT bits of USBCTL (R15),event occurs that requires the attention of the SPI mas-along with the VBCOMP comparator outputter. The SPI master must setthe IE bit in the CPUCTL(VBUS_DET), control the pullup resistor between V(R16) register to activate INT. When the IE bit isand D+, as shown in Table 2. Note that if VBGATE = 1CCcleared, INT is inactive (open for level mode, high forand VBUS_DET = 0, the pullup resistor is disconnectednegative edge, low for positive edge). INT is inactiveregardless of the CONNECT bit setting.
upon power-up or after a chip reset.
XI and XO
The INT pin can be a push-pull or open-drain output.XI and XO connect an external 12MHz crystal to theSet the INTLEVEL bit of the PINCTL (R17) register highinternal oscillator circuit. XI is the crystal oscillatorto program the INT output pin to be an active-low levelinput, and XO is the crystal oscillator output. Connect(open-drain output). An external pullup resistor to Vone side of an external 12MHz ±0.25% parallel reso-required for this setting. In level mode, the MAX3420ELisnant crystal to XI, and connect XO to the other side.drives INT low when any of the interrupt flags are set. IfConnect load capacitors (20pF max) to ground on bothmultiple interrupts are pending, INT goes inactive onlyXI and XO. XI can also be driven with an externalwhen the SPI master clears the last active interrupt12MHz ±0.25% clock. If driving XI with an externalrequest bit (Figure 10). The POSINT bit of the PINCTLclock, leave XO unconnected. The external clock must(R17) register has no effect on INT in level mode.
meet the voltage characteristics depicted in theClear the INTLEVEL bit to program INT to be an edgeElectrical Characteristicstable. Internal logic is single-(push-pull output). The active edge is programmableedge triggered. The external clock should have a nomi-using the POSINT bit of the PINCTL (R17) register. Innal 50% duty cycle.
edge mode, the MAX3420E produces an edge refer-enced to Vor when an interrupt request is cleared and others are
Lany time an interrupt request is activated,______________________________________________________________________________________
13

Connect load capacitors (20pF max) to ground on both XI and XO. XI can also be driven with an external 12MHz ±0.25% clock. If driving XI with...
Connect load capacitors (20pF max) to ground on both XI and XO. XI can also be driven with an external 12MHz ±0.25% clock. If driving XI with...
热门文档