文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > MAX3420EECJ+_3417509
侵权投诉

MAX3420EECJ+_3417509

MAX3420 -usb资料

USB Peripheral Controllerwith SPI InterfaceMAX3420E

Typical Operating Characteristics

(VCC= +3.3V, VL= +3.3V, TA= +25°C.)

EYE DIAGRAM

43D+ AND D- (V)

210-1

10

20

30

40

50

60

70

80

TIME (ns)

MAX3420E toc01

The MAX3420E contains the digital logic and analogcircuitry necessary to implement a full-speed USBperipheral that complies with the USB specification rev2.0. ESD protection of ±15kV is provided on D+, D-,and VBCOMP. The MAX3420E features an internal USBtransceiver and an internal 1.5kΩresistor that connectsbetween D+ and VCCunder the control of a register bit(CONNECT). This allows a USB peripheral to controlthe logical connection to the USB host.Any SPI mastercan communicate with the MAX3420E through the SPIslave interface that operates in SPI mode (0,0) or (1,1).An SPI master accesses the MAX3420E by reading andwriting to internal registers. A typical data transfer con-sists of writing a first byte that sets a register addressand direction with additional bytes reading or writingdata to the register or internal FIFO.

The MAX3420E contains 384 bytes of endpoint buffermemory, implementing the following endpoints: EP0: 64-byte bidirectional CONTROL endpoint

EP1: 2 x 64-byte double-buffered BULK/INTOUT endpoint

EP2: 2 x 64-byte double-buffered BULK/INT INendpoint

EP3: 64-byte BULK/INT IN endpointThe choice to use EP1, EP2, EP3 as BULK or INTER-RUPT endpoints is strictly a function of the endpointdescriptors that the SPI master returns to the USB hostduring enumeration.

12

The MAX3420E register set and SPI interface is optimizedto reduce SPI traffic. An interrupt output pin, INT, notifiesthe SPI master when USB service is required: when apacket arrives, a packet is sent, or the host suspends orresumes bus activity. Double-buffered endpoints helpsustain bandwidth by allowing data to move concurrentlyover USB and the SPI interface.

Power the USB transceiver by applying a positive 3.3Vsupply to VCC. Bypass VCCto GND with a 1.0µFceramic capacitor as close to the VCCpin as possible.

VCC

The MAX3420E digital core is powered though the VLpin. VL also acts as a reference level for the SPI inter-face and all other inputs and outputs. Connect VLto thesystem’s logic-level power supply. Internal level transla-tors and VLallow the SPI interface and all general-pur-pose inputs and outputs to operate at a system voltagebetween 1.71V and 3.6V.

VL

VBCOMP

The MAX3420E features a USB VBUSdetector input,VBCOMP. The VBCOMP pin can withstand input volt-ages up to 6V. Bypass VBCOMP to GND with a 1.0µFceramic capacitor. According to USB specification rev2.0, a self-powered USB device must not power the1.5kΩpullup resistor on D+ if the USB host turns offVBUS. VBCOMP is internally connected to a voltagecomparator so that the SPI master can detect the lossof VBUS(through an interrupt (INT) or checking a bit

______________________________________________________________________________________

上一页第12页

TOP相关主题

你可能喜欢

热门文档

相关文档

  • MAX3420EECJ中文资料

    Connect load capacitors (20pF max) to ground on both XI and XO. XI can also be driven with an external 12MHz ±0.25% clock. If driving XI with...

  • MAX3420EECJ中文资料

    Connect load capacitors (20pF max) to ground on both XI and XO. XI can also be driven with an external 12MHz ±0.25% clock. If driving XI with...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email