文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > MAX3420EECJ+_3417509
侵权投诉

MAX3420EECJ+_3417509

MAX3420 -usb资料

USB Peripheral Controllerwith SPI InterfaceMAX3420E

pending (Figure 10). Set the POSINT bit in the PINCTL(R17) register to make INT active high, and clear thePOSINT bit to make INT active low.

GPIN3–GPIN0, GPOUT3–GPOUT0 and GPX

The MAX3420E has four general-purpose inputs(GPIN3–GPIN0), four general-purpose outputs(GPOUT3–GPOUT0), and a multiplexed output pin(GPX). GPIN3 through GPIN0 all have weak internalpullup resistors to VL. These inputs can be read bysampling bits 7 through 4 of the IOPINS (R20) register.Writing to GPIN3 through GPIN0 has no effect.GPOUT3 through GPOUT0 are the general-purposeoutputs. Update these outputs by writing to bits 3through 0 of the IOPINS (R20) register. GPOUT3–GPOUT0 logic levels are referenced to the voltage onVL. As shown in Figure 11, reading the state of aGPOUT3–GPOUT0 bit returns the state of the internalregister bit, not the actual pin state. This is useful fordoing read-modify-write operations to an output pin(such as blinking an LED), since the load on the outputpin does not affect the register logic state.

GPX is a push-pull output with a 4-way multiplexer thatselectsits output signal. The logic level on GPX is refer-enced to VL. The SPI master writes to the GPXB and

GPXA bits of PINCTL (R17) register to select one of fourinternal signals as depicted in Table 3.

OPERATE:This signal goes high when theMAX3420E is able to operate after a power-up orRESreset. OPERATE is the default GPX output. VBUS_DET:VBUS_DET is the VBCOMP comparatoroutput. This allows the user to directly monitor theVBUSstatus.

BUSACT:USB BUS activity signal (active-high).This signal is active whenever there is traffic onthe USB bus. The BUSACT signal is set whenevera SYNC field is detected. BUSACT goes low duringbus reset or after 32-bit times of J-state.

SOF:A square wave with a positive edge that indicates the USB start-of-frame (Figure 12).

MOSI (Master-Out, Slave-In) and

MISO (Master-In, Slave-Out)

The SPI data pins MOSI and MISO operate differentlydepending on the setting of a register bit called FDUPSPI(full-duplex SPI). Figure 13 shows the two configurationsaccording to the FDUPSPI bit setting.

14______________________________________________________________________________________

上一页第14页

TOP相关主题

你可能喜欢

热门文档

相关文档

  • MAX3420EECJ中文资料

    Connect load capacitors (20pF max) to ground on both XI and XO. XI can also be driven with an external 12MHz ±0.25% clock. If driving XI with...

  • MAX3420EECJ中文资料

    Connect load capacitors (20pF max) to ground on both XI and XO. XI can also be driven with an external 12MHz ±0.25% clock. If driving XI with...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email