Summary the difference between 8620,9310H,4340 and 4320.
1. Specification:
Hardness requirement 58-63 HRC Core hardness: 27HRC On drawing :17CrNiMo6
DIN
GB/T 3077 20CrNiMoH 12CrNi3 17Cr2Ni2Mo 20CrMnMo 40CrNiMoA 20CrNi2Mo
SAE 8620 9310H 4119 4340 4320
EN10084 20CrNiMo2 13NiCr12 17CrNiMo6 20CrMo5 36NiCrMo4
C% 0.18/0.23 0.07/0.13 0.15/0.21 0.17/0.23 0.38/0.43 0.17/0.22
Si% 0.15/0.35
Mn% 0.7/0.9
Cr%
Ni%
Mo%
P% 0.025 0.025 ≤0.035 ≤0.035
A
Z
Ak 71 41 55 55 S% ≤0.040 0.015 0.035 ≤0.035 ≤0.040 ≤0.040






HRC 64 ≥56 57-62 50-62 51.5
0.40/0.60 0.40/0.70 0.15/0.25 ≤0.035
0.15/0.35 0.40/0.70 1.00/1.45 2.95/3.55 0.08/0.15 ≤0.40 0.17/0.37
0.5/0.9 0.9/1.2
1.5/1.8 1.1/1.4
1.4/1.7 -
0.25/0.35 0.2/0.3 0.2/0.3
Re
0.15/0.35 0.60/0.80 0.70/0.80 1.65/2.00
Heat treatment
Rb 1300 930 1080-1320 1175 1885 980
0.15/0.35 0.40/0.70 0.35/0.65 1.55/2.00 0.20/0.30 ≤0.035
Through harding steel case-hardening steels
SAE 8620 9310H 4119 4340 4320
DIN EN10084 20CrNiMo2 13NiCr12 17CrNiMo6 20CrMo5 36NiCrMo4
2. single quenched and tempered (150°C (300°F)), carburized
Carburized, quenched and tempered Carburized, quenched and tempered 850Quench 250 Temper
GB/T 3077 20CrNiMoH 12CrNi3 17Cr2Ni2Mo 20CrMnMo 40CrNiMoA 20CrNi2Mo
1033 11.5 51.6 685 785 885 1550
11 8 10 12 15
50 35 45 40 40
oil quenched 855°C (1570°F), 230°C (450°F) temper for 4 hrs.
Carburized, quenched and tempered
60.5
1
resistance and a further improvement of the materials wear and friction ...In fig. 1 the chain structure of Stanyl is shown in comparison to PA66...
Plastic gear selection for the application begins with review of the existing...Materials comparison Benefit Noise reduction Shock absorbtion Vibration damping ...
材料对照表Material Comparison Table 2011.01.25_机械/仪表_工程科技_专业资料... ASTM = American Society for Testing and Materials 2) UNS = Unified ...
Materials comparison_计算机软件及应用_IT/计算机_专业资料。Material comparison of Drawing and Chinese Serial NO. 1 2 3 4 5 Drawing Marerial designation ...
Landing Gear Definition The undercarriage or landing gear in aviation, is ...upper spindle attachment Main Landing Gear – Materials Thanks For Your ...
gear unit Areas of application In environmental engineering for the treatment ... material comparison Materials, mixer size/material combinations, recommended ...
sorts?of?materials?are?incorporated?for?a?variety...with?fabric?for?gear?wheels?or?with?paper?for?...By?comparison,?the?screws?used?in?thermoplastic?...
How to spec’ screws & Barrels For Running corrosive materials_机械/仪表_...payback Achieving energy savings Comparison of dryer and conveying system ...
– This causes the gear to turn and makes the center section move to ...Table 16.4 – Specification comparison for mold materials 12 Dr. Joseph ...
In comparison to machining, P/M gear manufacturing will certainly reduce raw...Sintered materials of interest were for the low Cr- and Mo-alloyed, fully...
热门文档