High-Performance Sintered-Steel Gears for Transmissions and
Machinery: A Critical Review
Dr.-Ing. Senad Dizdar
Management Summary
Except for higher-end gear appli-cations—found in automotive and aerospace transmissions, for exam-ple—high-performance, sintered-steel gears match wrought-steel gears in strength and geometrical quality. The enhanced P/M perfor-mance is due largely to advances in powder metallurgy over last two decades, such as selective surface densification, new materials and lubricants for high density and warm-die pressing. This paper is a review of the results of a decade of research and development of high-performance, sintered-steel gear pro-totypes at Höganäs AB.
Introduction
The mechanical power transmissions and machinery of today are designed and manufactured to meet the difficult demands of sustainable production, low cost, compact size, low weight, high efficiency, quiet operation, long service life and—when it ends—full recycling. And when comparing powder metallurgy (P/M)—sintered gears—with wrought steel gears, there is no doubt the latter have attained the best-possible levels in gear strength, geometry and material quality. In con-trast, while sintered-steel gears have also reached very high levels in gear strength, geometry and material qual-ity, they also offer highly sustainable production, low total cost and full recycling for a range of applications in the automotive, agricultural, construc-tion, power tools and home appliances industries.
Another method for making machined-sintered gears is the so-called blank concept. Here the gear blanks are manufactured by pressing and sintering, selective surface densi-fication and hardening, and are then sent for hard finishing to attain final geometrical quality. With this concept, production sustainability is enhanced by pressing geometrical features in the press direction and eliminating material waste, while also providing high gear
strength and material and geometrical quality.
Both sintered and sintered-machined gears are in step with global trends toward improvements in production sustainability. Table 1 lists results of a recently published study by the Metal Powder Industry Federation (MPIF); the analysis was done on a truck trans-mission notch segment, but the num-bers for gears will not much vary. In comparison to machining, P/M gear manufacturing will certainly reduce raw material needs—due to very lim-ited material loss—and at half the ener-gy used.
High-Performance Sintered GearsP/M entered gear applications through sintered pump gears in the early 1940s (Ref. 2). Since that time P/M has advanced in developing pressing technologies for high density such as selective surface densification (Ref. 3); warm compaction (Ref. 4); high-density lubricants and warm-die compaction (Ref. 5); fully pre-alloyed chromium steel powder grades such as Astaloy CrM, Astaloy CrL (Ref. 6) and, most recently, Astaloy CrA and high-density powder solutions, such as Hipaloy (Ref. 7).
Today it is readily possible to pro-duce spur and helical P/M gears with a
(First presented at International
Conference on Gears 2010,
Munich, Germany)
Table 1—Side-by-side comparison of truck transmission notch-segment manufacturing steps by Metal Powder Industries Federation (MPIF) (Ref. 1)
Manufacturing Finished part Raw material Material loss (g)Manufacturing Energy used60
GEARTECHNOLOGYdoc.guandang.net
High-performance Materials。很好的资料From the building blocks of iron and steel to the latest advances in polymers, ceramics, and composites, the 20th ...
High-performance Steel Wire Winding Hydraulic Hose Expansion of Luohe Letone Rubber Co._专业资料。sacpoetfJieohmilerhrjc o intcec l PraCopnyAt200o Jnur 1,...
Journal of Alloys and Compounds 408–412 (2006) 1344–1349 Proven technologies on high-performance Nd–Fe–B sintered magnets Yuji Kaneko a,? , ...
JULY 2001 A Novel High-Performance Magnetic Gear...Index Terms—Gearboxes, gears, magnetic circuits....sintered NdFeB permanent magnets, and the steel ...
and employs sintered NdFeB permanent magnets having a remanence of 1.25 T...lled with high performance epoxy and stainless steel clamping rods to be ...
13, No. 2 (2014) 255-270 DOI: http://dx.doi.org/10.12989/cac.2014.13.2.255 255 Performance and modeling of high-performance steel fiber ...
Published on Web 11/06/2009 High-Performance Zeolite NaA Membranes on ... they would be damaged because ceramic HFs must be sintered at high ...
High performance Sm-Fe-N magnets prepared by ...compact and then sintered at a high temperature ...The powder was placed on a hardened steel plate...
Published on Web 11/06/2009 High-Performance Zeolite NaA Membranes on ... they would be damaged because ceramic HFs must be sintered at high ...
Seismic performance of steel-reinforced recycled concrete columns under low ...Fig. 11b shows that the initial stiffnesses of the columns with high ...
热门文档