文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 材料科学 > Metals selection
侵权投诉

Metals selection

加热材料选择

HEAT TREATING/THERMAL EQUIPMENT HIGH TEMPERATURE ALLOYS Table 1– High-temperature alloys (in order of increasing performance) Material Carbon steel, such as ASTM A 387 Grade 22 (2-1/4Cr, 1Mo) 409 and 410S stainless (UNS S40900, S41008) 430 Stainless (S43000) 304/304H and 316L Stainless, (S30400/S30409, and S31600), cast HF 816°C 321 Stainless (S32100) 309S (S30908), cast HH-2 (J93633) Alloy 800HT (UNS N08811) RA 253 MA Alloy (UNS S30815) 310 (S31008) and cast HK (J94204) RA 330 Alloy (N08330, EN 1.4886) Temperature use limits 649°C (1200°F) Comments Above 510°C (950°F), 304H is stronger and more oxidation resistant.

650°C (1200°F), limited by oxidation Subject to embrittlement after several years of service above about 315°C (600°F). 870°C (1600°F) for useful oxidation resistance (1500°F), limited by oxidation 870°C (1600°F) 1010 to 1038°C (1850 to 1900°F) 1093°C (2000°F) 1100°C (2000°F) upper limit of oxidation resistance Very good oxidation resistance to 1093°C (2000°F) Tolerates rather extreme temperature abuse through 1200°C (2200°F) due to useful oxidation resistance and fairly high melting point Subject to embrittlement when exposed to the 315–600°C (600–1100°F) range. If product contamination by scale particles is a concern, consider a 650°C (1200°F) limitation. Has about a 55°C (100°F) advantage over 304. Unsatisfactory oxidation performance at higher temperatures. Stronger and somewhat more oxidation resistant than 309S. At higher temperatures, oxidation resistance may be adequate, but not exceptional. Drops off considerably by 1150°C (2100°F); 310 strength is quite low at these temperatures. Available in more product forms than almost any other high-temperature alloy; uses include muffles, retorts, radiant heating tubes, bar frame baskets in heat treat.

RA 353 MA Alloy (S35315, EN 1.4854 )

Melting point (solidus 1360°C/ Muffles and other components; tolerates extreme 2480°F) similar to that of RA 330 but temperatures better than RA 330. better oxidation resistance 1150°C (2100°F) About 1204°C (2200°F) in open air One of the strongest available wrought alloys up to about 1040°C (1900°F). Uses: retorts, rotary calciners, muffles for brazing, molybdenum and tungsten oxide reduction. High strength.

Alloy HR-120 RA 333 alloy (N06333)

625 (N06625) 601 (N06601) 602 CA Alloy X (N06002)

980°C (1800°F) Oxidation resistance

1204°C (2200°F) Oxidation resistance Uses: muffles, retorts, and radiant heating tubes. 1204°C (2200°F) Oxidation resistance Applications include CVD retorts and rotary with good strength

calciners. 1177°C (2150°F) in open air); Designed for gas turbine combustors where the 0.9% Mo may result in catastrophic hot gases continually sweep over the metal oxidation under stagnant conditions surface. 980 to 1090°C (1800 to 2000°F); very strong 1150 to 1204°C (2100 to 2200°F); strong alloy, with excellent oxidation resistance and good retention of ductility after intermediate temperature exposure 1204°C (2200°F); suited for extreme temperature conditions Uses: land-based gas turbine combustors and nitric acid catalyst support grids. Uses: gas turbine combustors, nitric acid grids, and CVD retorts.

Alloy 617 Alloy 230

Supertherm, cast 26Cr 35Ni 5W 15Co

Co content minimizes high- temperature galling wear in contact with NiCrFe alloys.

temperature range, many of the higher chromium alloys precipitate a brittle intermetallic compound known as sigma phase. Molybdenum contributes to this phase. Sigma reduces room temperature impact strength and ductility. The quantity and mor52

phology of the sigma phase determines the severity of embrittlement. Usually the metal is brittle only near room temperature, and retains reasonable ductility at operating temperatures above about 315 to 540°C (600 to 1000°F). Higher nickel grades such

as N08811, N08330, N06600, and N06601 are not susceptible to embrittlement by sigma. The cast heat-resistant alloys, being much higher in carbon, loose ductility due to heavy carbide precipitation in service. Strength. Creep-rupture proper-

HEAT TREATING PROGRESS NOVEMBER/DECEMBER 2003

Metals selection

上一页第2页

你可能喜欢

热门文档

相关文档

  • Materials Selection

    Ge material Selection 28页 5财富值喜欢此文档的还喜欢 MATERIALS SELECTION 35页 免费 Materials Selection Guid... 77页 免费 5. Materials Selection -... ...

  • Materials Selection for Engineering Design

    Materials Selection for Engineering Design_其它考试_资格考试/认证_教育专区。Materials Selection for Engineering Design Materials Selection ? ? ? The designer ...

  • CHAPTER 3 MATERIALS SELECTION

    CHAPTER 3: MATERIALS SELECTION 第三章 :材料选择 300 GENERAL 300 一般 a. While material selection cannot preclude system failures, proper material selection ...

  • Pump Material Selection

    PUMP MATERIALS SELECTION 材料的选择 刘丽香 Materials Selection材料的选择   API 610 Annex G, Materials class selection guidance API 610 Annex H, ...

  • ...Design Engineering and Selection of Materials_免...

    Chp 2 - Design Engineering and Selection of Materials 隐藏>> ME 215 – Engineering Materials I Chapter 2 – Design Engineering and Selection of ...

  • 9.材料选择及混粉设计-Material selection and powder ...

    9.材料选择及混粉设计-Material selection and powder mix design_材料科学_...materials 扩散预合金粉末十分适合于粉末冶金结构零件大规模生 产,而且在温压、...

  • 填充金属选择

    The following information is found in these lists : SIDEM' marks, identical to those of Filler metals selection tables. Trade name from main suppliers. ...

  • 7.1机械工程材料合理选用的基本原则

    7.1 机械工程材料合理选用的基本原则 Fundamentals of Rational Selection and application for Mechanical Engineering Materials ? 7.1.1 充分考虑材料的使用性能原则...

  • 德国DIN金属与非金属材料标准名称

    requirements on metallic materials for valves being used for gas appliances, notes for selection for materials, strength data DIN 30690-2-1980 供气装置中...

  • Materials

    Mapping the World of Materials: the first step in exploration and selection New approaches to Materials Education - a course authored by Mike Ashby and ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email