加热材料选择
HEAT TREATING/THERMAL EQUIPMENT HIGH TEMPERATURE ALLOYS ties at temperature are usually available from the various producers, and many alloys are covered by the ASME Boiler and Pressure Vessel Code. Oxidation. Chromium is the one element present in all heat-resistant alloys, the protective chromia scale being the basis for high-temperature environmental resistance. Nickel is next in importance, then silicon, aluminum, and rare earths. Oxidation rates in service depend upon thermal cycling and creep, which increase scale spalling. Also, contaminants such as alkali metal salts can damage the chromia scale, grain size can affect chromium diffusion rates, and the particular atmosphere involved is another factor. Significant water vapor content usually increases oxidation rates. Carburization. Chromium, nickel, and silicon are three major elements that confer resistance to absorption of carbon. Nickel and silicon lower the maximum solubility of carbon and nitrogen. Carburization is normally an issue because highly carburized alloys become brittle. Above about 1% carbon, most wrought heat-resistant alloys have no measurable room temperature ductility. Metal dusting, also know as catastrophic carburization or carbon rot, is a metal wastage, not an embrittlement phenomenon. In the right environment, it appears that any alloy can eventually produce metal dust. Overall, there is disagreement regarding appropriate a
lloy selection. In the steel heat treating industry, experience has shown that RA333 and Supertherm are two of the best choices. 602 CA performs well in some petrochemical applications, while 310 stainless has been used in petrochemical metal dusting environments. Alloys such as N08830 and N08811 do not perform well in metal dusting. Sulfidation. High chromium, low, or moderate nickel minimizes sulfidation attack at high temperature. With the exception of alloy HR-160, 20% or less nickel is preferred. Fabricability. This is not usually a significant issue with conventionally melted wrought alloys. Oxide dispersion strengthened grades such as MA956 offer unmatched strength and oxidation resistance at extreme temperature but are difficult to fabricate by conventional means. Design. Allowable stresses are
Fig. 2–– Bar baskets for carburizing plus oil quenching (top left), corrugated boxes for heat treatment of malleable white iron castings (bottom left), and trays for 815°C (1500°F) steel wire batch annealing (right), are all fabricated from RA 330. Courtesy, Rolled Alloys.
often based on ASME design allowables. For design stress, most thermal processing equipment uses either one half of the 10,000 hour rupture strength, or one half of the stress to cause a minimum creep rate of 1% in 10,000 hours. Above about 540°C (1000°F), creep or rupture is the basis for setting design stresses. Materials are no longer elastic, but deform slowly with time. Thermal Expansion. A major cause of distortion and cracking in high-temperature equipment is failure to adequately address the issue of thermal expansion, and differential thermal expansion. Temperature gradients of only 110°C (200°F) are sufficient to strain metals beyond the yield point. Molten Metals. The molten metals most likely to cause an industrial
Fig. 3–– Muffle (top), still operating after a year, is used for copper brazing and bright annealing operations at 1150°C (2100°F) and pack aluminizing retort (bottom). Both are made of RA 353 MA. Courtesy, Rolled Alloys.
HEAT TREATING PROGRESS NOVEMBER/DECEMBER 2003
53

Ge material Selection 28页 5财富值喜欢此文档的还喜欢 MATERIALS SELECTION 35页 免费 Materials Selection Guid... 77页 免费 5. Materials Selection -... ...
Materials Selection for Engineering Design_其它考试_资格考试/认证_教育专区。Materials Selection for Engineering Design Materials Selection ? ? ? The designer ...
CHAPTER 3: MATERIALS SELECTION 第三章 :材料选择 300 GENERAL 300 一般 a. While material selection cannot preclude system failures, proper material selection ...
PUMP MATERIALS SELECTION 材料的选择 刘丽香 Materials Selection材料的选择 API 610 Annex G, Materials class selection guidance API 610 Annex H, ...
Chp 2 - Design Engineering and Selection of Materials 隐藏>> ME 215 – Engineering Materials I Chapter 2 – Design Engineering and Selection of ...
9.材料选择及混粉设计-Material selection and powder mix design_材料科学_...materials 扩散预合金粉末十分适合于粉末冶金结构零件大规模生 产,而且在温压、...
The following information is found in these lists : SIDEM' marks, identical to those of Filler metals selection tables. Trade name from main suppliers. ...
7.1 机械工程材料合理选用的基本原则 Fundamentals of Rational Selection and application for Mechanical Engineering Materials ? 7.1.1 充分考虑材料的使用性能原则...
requirements on metallic materials for valves being used for gas appliances, notes for selection for materials, strength data DIN 30690-2-1980 供气装置中...
Mapping the World of Materials: the first step in exploration and selection New approaches to Materials Education - a course authored by Mike Ashby and ...
热门文档