文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 材料科学 > Metals selection
侵权投诉

Metals selection

加热材料选择

HEAT TREATING/THERMAL EQUIPMENT HIGH TEMPERATURE ALLOYS

MATERIALS SELECTION CONSIDERATIONS Materials used have a significant effect on thermal efficiency, productivity, and operating costs. by James Kelly* Rolled Alloys Corp. Temperance, Mich. igh temperature metallic materials or alloys used in process heating equipment (furnaces, heaters, ovens, kilns, etc.) have a significant effect on thermal efficiency, productivity, and operating cost of the equipment. These materials are used in burners, electrical heating elements, material handling, load support, heater tubes, and many other components. A number of factors must be considered to select appropriate materials to improve energy efficiency of the equipment while extending their life at minimum cost. These factors include mechanical properties, oxidation or hot corrosion resistance, use of cast or fabricated components, and material availability. Technical data describing the properties of heat-resistant alloys are necessary guides to alloy selection. Not unexpectedly, the behavior of alloys during long exposure to various hightemperature environments is complex. This behavior is not always completely predicted by laboratory tests alone. Service experience with high-

FOR THERMAL PROCESSING EQUIPMENT

0

temperature equipment is needed to develop the judgment to determine the relative significance of the many variables involved. Selection criteria Factors in addition to estimated service temperature should be taken into account when selecting alloys for hightemperature use. Operating temperature. Temperature is often the first— and sometimes the only— data point given upon which one is supposed to base alloy selection. However, in practice, one cannot successfully choose an alloy based on temperature alone. Nevertheless, one simple first guide to alloy selection is an estimate of the maximum temperature at which a given alloy might have useful long-term engineering properties. Considering oxidation in air as the limiting factor, several common alloys rate as shown in Table 1. These ratings apply to plate form; thin sheet will have a lower limiting temperature due to proportionally greater losses from oxidation. Thermal Stability. After long exposure to the 590–870°C (1100–1600°F)

and Arvind Thekdi** E3M, Inc. North Potomac, Md.

MATERIAL SELECTION CRITERIA For optimal performance in service, selection criteria for high-temperature alloys depends not only on temperature, but also on other important environmental factors that a component will see in service. A more comprehensive list includes: Operating Temperature Thermal stability Strength Oxidation Carburization Sulfidation Fabricability Design stress Thermal expansion Molten metal contact Galling considerations *Member of ASM International **Member of ASM International and the ASM Heat Treating Society

Fig. 1— Radiant tubes for annealing furnaces are fabricated of RA 253 M

A. Typical operating temperature is 980°C (1800°F) in an exothermic atmosphere for horizontally mounted U- tubes (left) shown after 10 months service. Radiant tubes for hydrogen annealing of steel rod and/or sheet coil are made of the same alloy, while the inner covers are 309 stainless steel (right). Courtesy, Rolled Alloys.

HEAT TREATING PROGRESS NOVEMBER/DECEMBER 2003

51

Metals selection

第1页

你可能喜欢

热门文档

相关文档

  • Materials Selection

    Ge material Selection 28页 5财富值喜欢此文档的还喜欢 MATERIALS SELECTION 35页 免费 Materials Selection Guid... 77页 免费 5. Materials Selection -... ...

  • Materials Selection for Engineering Design

    Materials Selection for Engineering Design_其它考试_资格考试/认证_教育专区。Materials Selection for Engineering Design Materials Selection ? ? ? The designer ...

  • CHAPTER 3 MATERIALS SELECTION

    CHAPTER 3: MATERIALS SELECTION 第三章 :材料选择 300 GENERAL 300 一般 a. While material selection cannot preclude system failures, proper material selection ...

  • Pump Material Selection

    PUMP MATERIALS SELECTION 材料的选择 刘丽香 Materials Selection材料的选择   API 610 Annex G, Materials class selection guidance API 610 Annex H, ...

  • ...Design Engineering and Selection of Materials_免...

    Chp 2 - Design Engineering and Selection of Materials 隐藏>> ME 215 – Engineering Materials I Chapter 2 – Design Engineering and Selection of ...

  • 9.材料选择及混粉设计-Material selection and powder ...

    9.材料选择及混粉设计-Material selection and powder mix design_材料科学_...materials 扩散预合金粉末十分适合于粉末冶金结构零件大规模生 产,而且在温压、...

  • 填充金属选择

    The following information is found in these lists : SIDEM' marks, identical to those of Filler metals selection tables. Trade name from main suppliers. ...

  • 7.1机械工程材料合理选用的基本原则

    7.1 机械工程材料合理选用的基本原则 Fundamentals of Rational Selection and application for Mechanical Engineering Materials ? 7.1.1 充分考虑材料的使用性能原则...

  • 德国DIN金属与非金属材料标准名称

    requirements on metallic materials for valves being used for gas appliances, notes for selection for materials, strength data DIN 30690-2-1980 供气装置中...

  • Materials

    Mapping the World of Materials: the first step in exploration and selection New approaches to Materials Education - a course authored by Mike Ashby and ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email