copper wire introduction
Figure 3c. Cu bond pad after die attached curing
(snap cured). 3.3 Plasma Cleaning
Plasma cleaning prior to wire bonding would help to ensure copper bond pad cleanliness by removing the copper oxide. However, it is a known fact that without the appropriate set up, plasma cleaning could do more harm than good. In this evaluation, the wire bond is carried out without plasma cleaning.
4. Wire Bonding
The wire bonding was carried out on the ASM Wire Bonder AB339 Eagle. Both gold and copper wires were used. Figures 4a and 4b show the gold wire and copper wire ball bond on the copper die. Figure 4c shows a SEM picture of the copper ball bond.
Figure4a. Au wire ball bond on Cu bond pad
Figure 4b. Cu wire ball bond on Cu bond pad
Figure 4c. SEM picture of Cu ball bond
- 3 -
4.1 Influence of the Bonding Stage Temperature
It is well known that copper oxidize readily when expose to high temperature. Hence, the following experiment is carried out to study the influence of the bonding stage temperature. A ball bond was bonded onto the copper die at an interval of 15 seconds. The bonding continued until non-stick of the ball bond occurred. The non-stick of ball bond is an indication of oxidation of the copper bond pad. This is related to the rate of oxidation. This same evaluation is carried out at different bonding temperature ranging from 145 C to 170 C. Figure 5a shows the relationship between the stage temperature and oxidation rate. For a stage temperature of 145 C, it has been observed that there is no non-stick at even after 6 minutes of exposure. Figure 5b shows the ball shear test carried on this unit. It could be seen that there is no decrease in the ball shear strength after 6 minutes.

Figure 5a. Relationship between the stage temperature and oxidation rate (non-stick of ball
bond)

Figure 5b. Relationship between ball shear and bond
stage exposure time at 145 C
5. Analysis of Copper Bond Pad Surface with OIM

It

has

been

observed that within the same lot of wafers, some are bondable even without plasma cleaning whereas some are not. This is most likely due to the oxidation of copper and pad surface. One of the advanced techniques for detecting the initial stages of oxidation
Copper Wire Bonding Training 铜线焊线培训 Prepared by: Ning wy Shenzhen STS Microeletronics Copper Wire Bonding Content of Presentation 内容介绍 Advantages优点...
Drivers for Cu Wire Bonding ? ? ? ? Cost, cost and cost Gold price continues to increase: $1,515.17/oz on 2011-05-04 Copper: $4.15/lb Early...
Wire Bonding Optimizatio... 6页 20财富值 Gold Wire Bonding On Low... ...The study has shown the utilization of advanced wire bonder copper capability...
wire bonding工艺文件 12页 2下载券 Copper Wire Bonding 5页 7下载券 喜欢...REJECT if no gold ball and or wire observed on bond pad and substrate ...
Market Review Challenges in Copper Wire bonding Heraeus Copper Wire Portfolio ...? Soft wire characteristics enable: ? Bonding on challenging pad structure. ...
In present paper, copper wire bonding on palladium finish and gold finish was studied to investigate the interface degradation during uHAST comparing with ...
Hardening: Advanced deformation, diffusion initiate Saturation: Bond finished ... Fine Pitch Copper Wire... 8页 免费 Wire Bonding Summary 25页 免费 ...
Development of Copper Wi... 6页 20财富值 ... Advanced Bonding Interconnection Technology (Chapter...Bonding styles – Al wire bonding on Cu pad, ...
(<=1.3mil) ~ 26% of the TAM Bonding Wire 18 Copper Wire Market Trend...Materials Characteristics of Soft Copper Wires Designed for Advanced Applications...
Many studies have been done on copper wire bonding for equipment capability,...Also, an advanced tip surface finishing in order to executes better gripping...
热门文档