文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电子/电路 > ADVANCED WIRE BONDING-BONDING ON COPPER
侵权投诉

ADVANCED WIRE BONDING-BONDING ON COPPER

copper wire introduction

used here was Orientation Imaging Microscopy (OIM). This technique is mainly used for local texture imaging and measurement. An electron beam scans the sample surface by means of a standard SEM. The sample is tilted at an angle of 70° towards a low-light camer. The emitted Electron Back-Scattered Diffraction (EBSD) patterns [6] is indexed and the crystallographic orientation of the area is determined. In this experiment, the samples were analyzed by means of Philips XL-20 SEM equipped with a TSL OIM software. The OIM map is generated by means of shading each point on the grid with respect to the crystal orientation. These OIM maps provide information on the crystallographic microtexture and microstructure. EBSD pattern is formed only from the top 10-50 nm layer of the sample. Therefore the method is very sensitive to surface contamination or oxidation, which regions are simply poorly indexed. Typically, further data handling is required to filter out orientation points that are wrongly indexed. In this work, filtering was done based on the confidence index (CI), assuming that patterns with CI > 0.1 are generally correctly indexed. Therefore, the reported OIM maps are cleared for points with CI < 0.1, which appear on them as black areas. These are the oxidized regions. More details about this new application of the OIM technique could be found elsewhere [7]. The original colours, which represent different orientations parallel to the surface normal, are represented here with different light gray levels in order not to be confused with the dark (oxidated) areas. Figures 6a and 6b shows that the main difference between bondable and non-bondable Cu surface is the level of

ADVANCED WIRE BONDING-BONDING ON COPPER

oxidation.

ADVANCED WIRE BONDING-BONDING ON COPPER

Figure 6a. OIM map on Cu pad surface (bondable)

Figure 6b. OIM map on Cu pad surface (unbondable) Compared to the bondable surface, the non-bondable shows initial stages of oxidation (appearing as black areas). The oxidized area can be estimated as being 10-20% of the bond pad surface. As expected, the oxidation begins at triple points and grain boundaries. Additionally, it has been found that the oxidation is also orientation

- 4 -

dependent, i.e. some orientation are oxidizing faster than others [7]. Summarizing, oxidized areas of the bond pad as little as 10-20% lead already to drastic changes in the bondability of Cu wire to Cu bond pad.

6. Surface Treatment on Copper Bond Pad

The copper pads need protection from oxidation after finishing the wafer. This is important for the further handling, testing and shipment of the wafers. Two different techniques are possible. A first method consists of applying an organic coating layer. A second approach is the capping of the copper pads with a metal layer. In this study, the initial result of the organic coating layer is discussed.

This organic coating layer is able to prevent oxidization of copper bond pad starting from wafer dicing up to wire bonding. Figure 7 shows a organic coated copper pad after dicing process. Comparing this to Figure 2b, it can be seen that though there are tiny particles gathering around the edges of the bond pad (probably silicon dust), the colour of the bond pad under optical microscope indicates that it has not been oxidized.

Figure 7. Organic coated Cu bond pad after dicing A simple DOE experiment with different bonding parameter settings was carried out to wire bond gold wire onto the organic coated copper bond pad, without plasma cleaning. Figure 8a shows the average ball shear strength results for the normal bond pad and bond pad with oxide studs. The ball diameter on both types of bond pad is the same because bonding was carried out on the test die at the same time. Therefore, it can be seen that the oxide studs pad has a higher ball shear strength than the normal pad. The average ball diameter is in the range of 60 m to 70 m. This 2gives a ball shear strength of 1.9gf/mil2 to 6.3gf/mil for the normal pad and 3.2gf/mil2 to 6.2gf/mil2 for the oxide studs pad. The actual contact area, being smaller than the measured ball diameter [8], would produce higher ball shear strength per area. Figures 8b and 8c show the typical failure mode of the ball shear area for the normal pad and that with oxide studs.

We are still in the process of fine tuning the bonding parameters for copper wire. The ball shear strength varies from 15gf to 30gf with different parameters setting. Figure 9 shows the failure mode for a ball shear of 26gf. The ball shear was carried out after exposing the bond pad to a higher temperature to reveal the oxidation of copper for colour contrast.

ADVANCED WIRE BONDING-BONDING ON COPPER

上一页第4页

你可能喜欢

热门文档

相关文档

  • Copper_Wire_Bonding_Training

    Copper Wire Bonding Training 铜线焊线培训 Prepared by: Ning wy Shenzhen STS Microeletronics Copper Wire Bonding Content of Presentation 内容介绍 Advantages优点...

  • Developments in Copper Wire Bonding

    Drivers for Cu Wire Bonding ? ? ? ? Cost, cost and cost Gold price continues to increase: $1,515.17/oz on 2011-05-04 Copper: $4.15/lb Early...

  • Fine Pitch Copper Wire Bonding Process and Material...

    Wire Bonding Optimizatio... 6页 20财富值 Gold Wire Bonding On Low... ...The study has shown the utilization of advanced wire bonder copper capability...

  • Wire bonding workmanship standard

    wire bonding工艺文件 12页 2下载券 Copper Wire Bonding 5页 7下载券 喜欢...REJECT if no gold ball and or wire observed on bond pad and substrate ...

  • Heraeus Copper Wire Presentation

    Market Review Challenges in Copper Wire bonding Heraeus Copper Wire Portfolio ...? Soft wire characteristics enable: ? Bonding on challenging pad structure. ...

  • Reliability of copper wire bonding in humidity envi...

    In present paper, copper wire bonding on palladium finish and gold finish was studied to investigate the interface degradation during uHAST comparing with ...

  • Wire Bonding process

    Hardening: Advanced deformation, diffusion initiate Saturation: Bond finished ... Fine Pitch Copper Wire... 8页 免费 Wire Bonding Summary 25页 免费 ...

  • Chapter7_Reliability_Advanced_bonding_interconnecti...

    Development of Copper Wi... 6页 20财富值 ... Advanced Bonding Interconnection Technology (Chapter...Bonding styles – Al wire bonding on Cu pad, ...

  • Cu wire bonding

    (<=1.3mil) ~ 26% of the TAM Bonding Wire 18 Copper Wire Market Trend...Materials Characteristics of Soft Copper Wires Designed for Advanced Applications...

  • ...and Feasibility of Copper Wire bonding for Non-h...

    Many studies have been done on copper wire bonding for equipment capability,...Also, an advanced tip surface finishing in order to executes better gripping...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email