source and an optical spectrum analyzer. In addition, the splice loss between the SMF28 and the DCF is ~1 dB. 0
-4
-8
-12
(dB)-16-20
-24
-28
-32
-36
Wavelength (nm)
Fig. 2. The transmission and reflection spectra of the proposed scheme before etchingof the
DCF.
The reflected power in the lowest order cladding mode is ~-5.3 dB since the maximum value for transmission by inner cladding modes is 33.5% in the second branch of the DCFC coupler between 1500 nm and 1547 nm (see Fig. 3). The characterization of the spectral response of the DCFC inner cladding transmission is achieved by using a wavelength-swept source and a diffuser. The diffuser is used to excite the high and low order modes in the inner cladding of the DCF [9].

In order to improve the efficiency of our device to capture greater number of the back reflected cladding modes at the splice between the FBG photosensitive fiber and the inner cladding of the DCF, the cladding diameter of the photosensitive SMF and the inner cladding diameter of the DCF have to be matched by decreasing the SMF diameter by 20 μm. This is achieved by etching the SMF, removing 20 μm of the cladding. In our scheme, the etched transition region (see Fig. 1) consists of the FBG in the photosensitive SMF and a small part of the DCF. To ensure better wet etch uniformity, a buffered oxide etch (BOE) [diluted HF with ammonium fluoride (NH4F)] is used to slow down the etch rate of SiO2 and to promote more uniform etching of the glass surface. The dilution ratio used in our experiment was 7:1 NH4F:HF. The reflection spectra in Fig. 4 show that decreasing the diameter by 20 µm increases the captured higher order modes significantly and increases the power of the captured low order modes as well.
Figure 5 shows both the reflection and transmission spectra of the device after HF wet etching. It can be seen that both low and high order modes, which are excited by the FBG can be recaptured efficiently by the proposed scheme. The captured cladding modes are within #181754 - $15.00 USDReceived 14 Dec 2012; revised 7 Feb 2013; accepted 25 Feb 2013; published 12 Mar 2013
(C) 2013 OSA25 March 2013 / Vol. 21, No. 6 / OPTICS EXPRESS 6876
A Novel Fiber Bragg Grating Sensor with_专业资料。光纤光栅A Novel Fiber ...The central wavelength of light reflected from an FBG is called the Bragg...
Temperature-independent acceleration with a strain-chirped fiber Bragg grating ...Experimental results show that 3-dB bandwidth and reflected optical power of...
a fiber Bragg grating_电子/电路_工程科技_专业...In the FBG, the reflected light is guided ...coupling of the core mode to the cladding modes...
Temperature Compensation for Double Fiber Bragg Grating Sensors_专业资料。维普资讯 http://www.cqvip.com WANG u-hn ,LU i,ZChncegIJa HENG inbn Ja-ag(....
Sensors and Actuators B 96 (2003) 468–472 Demonstration of etched cladding ?ber Bragg grating-based sensors with hydrogel coating Xiaomei Liu a , ...
Application of Fiber bragg Grating Sensors on ...The center wavelength b of the reflected spectral...
Fiber Grating 暂无评价 22页 免费 Fiber- Op tic Bragg- G... 3页 免费 光栅传感fiber optic br... 10页 1下载券 A Fiber...
Fiber-Bragg-grating-based seismic geophone for_理学_高等教育_教育专区。Optical Engineering 45 8 , 084404 August 2006 Fiber-Bragg-grating-based seismic ...
Any change in the fiber grating’s properties, such as strain, pressure, temperature or vibration, will change the reflected Bragg wavelength [4-8]. ...
microstructured fiber Bragg grating refractive index ...According to the mode analysis of a double-... or cladding modes can easily interact with the ...
热门文档