the wavelength band of 1500 nm and 1547 nm. Low order modes are captured very effectively, and the weakest high order mode are also well resolved and exceed 8 dB above the noise level, which can therefore be used in sensing. The different individual cladding modes can be easily discriminated and tracked.

Wavelength (nm) Reflection (dB)
Fig. 4. The reflection spectra of the proposed scheme with the fiber diameter decreased by 10,
18 and 20 ± 0.2 µm by wet etching.
Although the coupling loss of the DCFC increases with higher order cladding modes, there is sufficient discrimination even for the 41st cladding mode, to be used for sensing (see Fig. 5). The reflected power in the highest order cladding modes shown in Fig. 5 should ideally reach 12 to 14 dB including the 4.8 dB coupler loss. However, the splice loss between the SMF and the DCF of ~1 dB needs to be optimised, as this affects higher order modes more severely than lower order modes.
-4
-8
-12
(dB)-16-20
-24
-28
-32
-36
151015201530154015501560
Wavelength (nm)
Fig. 5. The reflection (red curve) and the transmission (black curve) spectra of the proposed
device after wet etching by 20 µm.
To demonstrate that the proposed scheme can be adapted as an evanescent wave based sensor, we characterize the response of the device to different surrounding refractive index (SRI) liquids from 1.30 to 1.51 (Cargille refractive index matching liquids).
Figure 6 shows the reflection spectra in response to different SRI. It can be seen that for SRI of 1.30, all the higher order modes can be discriminated and few high cladding modes are affected giving a spectra similar to that shown in Fig. 5 where the SRI is air. Increasing the SRI affects the higher order modes which disappear first, followed by the more confined cladding modes until all the cladding modes including the low order modes disappear at an SRI of 1.51. As the SRI gradually approaches and then exceeds the effective refractive indices of the cladding modes, they can no longer exist as bound modes and hence the high order modes are attenuated first. As is obvious, monitoring the Bragg reflection simultaneously allows self-referencing of the ambient temperature during measurements. #181754 - $15.00 USDReceived 14 Dec 2012; revised 7 Feb 2013; accepted 25 Feb 2013; published 12 Mar 2013
(C) 2013 OSA25 March 2013 / Vol. 21, No. 6 / OPTICS EXPRESS 6877
A Novel Fiber Bragg Grating Sensor with_专业资料。光纤光栅A Novel Fiber ...The central wavelength of light reflected from an FBG is called the Bragg...
Temperature-independent acceleration with a strain-chirped fiber Bragg grating ...Experimental results show that 3-dB bandwidth and reflected optical power of...
a fiber Bragg grating_电子/电路_工程科技_专业...In the FBG, the reflected light is guided ...coupling of the core mode to the cladding modes...
Temperature Compensation for Double Fiber Bragg Grating Sensors_专业资料。维普资讯 http://www.cqvip.com WANG u-hn ,LU i,ZChncegIJa HENG inbn Ja-ag(....
Sensors and Actuators B 96 (2003) 468–472 Demonstration of etched cladding ?ber Bragg grating-based sensors with hydrogel coating Xiaomei Liu a , ...
Application of Fiber bragg Grating Sensors on ...The center wavelength b of the reflected spectral...
Fiber Grating 暂无评价 22页 免费 Fiber- Op tic Bragg- G... 3页 免费 光栅传感fiber optic br... 10页 1下载券 A Fiber...
Fiber-Bragg-grating-based seismic geophone for_理学_高等教育_教育专区。Optical Engineering 45 8 , 084404 August 2006 Fiber-Bragg-grating-based seismic ...
Any change in the fiber grating’s properties, such as strain, pressure, temperature or vibration, will change the reflected Bragg wavelength [4-8]. ...
microstructured fiber Bragg grating refractive index ...According to the mode analysis of a double-... or cladding modes can easily interact with the ...
热门文档