
Fig. 1. Schematic of the proposed device to characterize the reflection spectrum.
The DCFC is made by fusing and tapering two DCFs [9]. The fibers are stripped of their protective jacket, cleaned, installed and inspected on a custom-made fiber coupler fabrication station. As a first step, the fibers are fused at high temperature using an oxy-propane micro-torch. The torch, mounted on a three-axis motorized stage, moves back and forth along the fibers to control the fusion length. As a second step, both ends of the structures are pulled apart using two additional motorized stages moving at a speed of 50 µm/s. The optical response is measured in real-time during fabrication. The DCF (Nufern, East Granby, CT, SM-9/105/125-20A) has a core diameter of 9 μm, an inner cladding diameter of 105 μm and fluorine-doped outer cladding diameter of 125μm of lower refractive index. The numerical aperture (NA) of the single mode core of the DCF is 0.12 and the inner cladding NA is 0.20. Our optical spectrum analyzer could accommodate a maximum light guiding diameter of only 62 micron and was therefore insufficient for the 105 micron inner cladding diameter in our experiments. We therefore used an integrating sphere power meter which has an entrance slit of 2.2 mm connected to the DCFC. The back reflected cladding modes are collected at the splice between the photosensitive fiber and the DCF by the inner cladding of the DCF and routed to the power meter by the second branch of the DCFC (see Fig. 1).
The FBG was imprinted in a photosensitive fiber by a commercially available 224 nm Nd:YVO4 laser which produces pulses of 7 ns an energy of 30 μJ at a repetition frequency of between 0.1 and 30 kHz with a maximum average power of 300 mW (Xiton Photonics). The beam is about 1 mm in diameter and is slightly elliptical. This laser has an excellent beam profile and stable laser output. It has a high wall-plug efficiency compared to the Argon laser used in the past for FBG fabrication [10]. A mirror on a linear translation stage was used to scan the fiber, and a 20 cm cylindrical lens is used to focus the light. A Bragg wavelength at 1554.5 nm was imprinted with a length of 12 mm.
3. Results and discussion
Figure 2 shows the transmission and the reflection spectra in the proposed scheme normalized with respect to the transmitted power at 1560 nm. The transmission spectra consist of two bands, a strong Bragg resonance at 1554.5 nm and several narrow resonances, which are the cladding modes on the short wavelength side of the Bragg resonance. The cladding mode resonances begin at a wavelength of 1547 nm and consist of relatively strong low order modes, which are more confined and propagate at low angles. It can be seen that the reflection spectra of the cladding modes consist of modes within a wavelength band from 1543 nm to 1547 nm, which complements a limited sub-set of the cladding mode resonances seen in the transmission spectra.
Characterisation of the coupler response is shown in Fig. 3. These experiments were conducted by exciting the port where the FBG was situated but without the FBG in place. The DCFC was designed to act as a null coupler for the core mode and as an 50:50 coupler for the inner cladding modes from 1265 to 1325 nm [9]. At 1555 nm, the measured power in the core mode in the second branch where the reflected light from the DCFC is measured reaches ~-11.5 dB including the 10.5 dB coupler loss (see Fig. 3). The characterization of the spectral response of the DCFC core transmission is achieved with a conventional broadband #181754 - $15.00 USDReceived 14 Dec 2012; revised 7 Feb 2013; accepted 25 Feb 2013; published 12 Mar 2013
(C) 2013 OSA25 March 2013 / Vol. 21, No. 6 / OPTICS EXPRESS 6875
A Novel Fiber Bragg Grating Sensor with_专业资料。光纤光栅A Novel Fiber ...The central wavelength of light reflected from an FBG is called the Bragg...
Temperature-independent acceleration with a strain-chirped fiber Bragg grating ...Experimental results show that 3-dB bandwidth and reflected optical power of...
a fiber Bragg grating_电子/电路_工程科技_专业...In the FBG, the reflected light is guided ...coupling of the core mode to the cladding modes...
Temperature Compensation for Double Fiber Bragg Grating Sensors_专业资料。维普资讯 http://www.cqvip.com WANG u-hn ,LU i,ZChncegIJa HENG inbn Ja-ag(....
Sensors and Actuators B 96 (2003) 468–472 Demonstration of etched cladding ?ber Bragg grating-based sensors with hydrogel coating Xiaomei Liu a , ...
Application of Fiber bragg Grating Sensors on ...The center wavelength b of the reflected spectral...
Fiber Grating 暂无评价 22页 免费 Fiber- Op tic Bragg- G... 3页 免费 光栅传感fiber optic br... 10页 1下载券 A Fiber...
Fiber-Bragg-grating-based seismic geophone for_理学_高等教育_教育专区。Optical Engineering 45 8 , 084404 August 2006 Fiber-Bragg-grating-based seismic ...
Any change in the fiber grating’s properties, such as strain, pressure, temperature or vibration, will change the reflected Bragg wavelength [4-8]. ...
microstructured fiber Bragg grating refractive index ...According to the mode analysis of a double-... or cladding modes can easily interact with the ...
热门文档