1. Introduction
Cladding modes are guided modes which can be excited easily by scattering light from the core of an optical fiber into the cladding [1]. FBG excited cladding modes are traditionally observed as a series of resonance peaks on the short wavelength side of the transmission spectrum of an FBG [2], due to the limited overlap of the field of the cladding modes with the guided mode field and the refractive index change across the core. These modes can also be excited with high efficiency as seen in the spectrum of a tilted fiber Bragg grating (TFBG)
[2]. These are generally not observed in the reflection spectrum since they may be dissipated through propagation along the high-index polymer jacket of the fiber [1]. Recently, many schemes have been proposed to re-couple the reflected cladding modes back into the core. For example, a sensor has been proposed to re-couple cladding modes into the core of a short fiber excited by tilted fiber Bragg grating (TFBG) in which the sensor fiber was spliced to misaligned fiber [3,4]. The sensor was used to measure the ambient refractive index, as a bend and vibration sensor [3,4]. Such SRI sensor provides a dynamic range from 1.33 to 1.45 with sensitivity of 1100 nW/RIU at 1.33.The re-coupled cladding modes are within the wavelength band of 1538 nm and 1551 nm as merged band with no discrimination between individual cladding modes [4]. Another scheme to re-couple low order cladding modes excited by the TFBG in the core used an abrupt bi-conical fused taper [5].
Cladding modes have also been re-coupled into the core with a TFBG in which a short multimode fiber or a thin-core fiber section with a mismatched core diameter section was spliced between a single mode fiber and the TFBG [6]. The recoupled cladding modes in the best-case scenario are within the wavelength band of 1541 nm and 1549 nm. The sensor was used to measure the different refractive indices of glycerine-water solutions surrounding the TFBG providing a dynamic range from 1.33 to 1.45 RIU.
A scheme to couple the cladding modes into the core using a hybrid long period grating (LPG) and an FBG device has also been demonstrated. Here, the forward propagating core mode is partially coupled by the LPG into a cladding mode, which in turn is reflected with the core mode by a subsequent FBG, and partially re-coupled into the core by the same LPG
[7,8].
One of the problems in all these devices is that, generally when a large number of cladding modes are involved, it is difficult to capture all the modes within a large wavelength band. An efficient discrimination between individual cladding modes is another problem to consider.
In this paper, we present a novel and simple device, which is capable of measuring cladding modes efficiently including both low-order, as well as higher order cladding modes propagating at steeper angles, which are more sensitive to the surrounding medium. We use the reflection from a single FBG in a standard photosensitive single mode fiber to couple the cladding modes into the inner cladding of a fusion spliced and diameter-matched DCF. The signal is viewed on the return port of a double-clad fibre coupler (DCFC).
2. Experimental procedure
The DCF has a single mode core, a lower index first cladding and a depressed outer cladding. Our device consists of a DCFC, whose single mode core is excited by a standard single mode fiber (SMF) spliced to one of its two branches and connected to a swept wavelength system (SWS) in a wavelength range between 1500 and 1560 nm (branch 1), and is schematically shown in Fig. 1. A single mode photosensitive fiber with an imprinted FBG is fusion spliced to the DCF a short distance away (~5 mm). The device is characterized by measuring the reflected core and cladding light through the DCFC (branch 2) on an oscilloscope.
#181754 - $15.00 USDReceived 14 Dec 2012; revised 7 Feb 2013; accepted 25 Feb 2013; published 12 Mar 2013
(C) 2013 OSA25 March 2013 / Vol. 21, No. 6 / OPTICS EXPRESS 6874
A Novel Fiber Bragg Grating Sensor with_专业资料。光纤光栅A Novel Fiber ...The central wavelength of light reflected from an FBG is called the Bragg...
Temperature-independent acceleration with a strain-chirped fiber Bragg grating ...Experimental results show that 3-dB bandwidth and reflected optical power of...
a fiber Bragg grating_电子/电路_工程科技_专业...In the FBG, the reflected light is guided ...coupling of the core mode to the cladding modes...
Temperature Compensation for Double Fiber Bragg Grating Sensors_专业资料。维普资讯 http://www.cqvip.com WANG u-hn ,LU i,ZChncegIJa HENG inbn Ja-ag(....
Sensors and Actuators B 96 (2003) 468–472 Demonstration of etched cladding ?ber Bragg grating-based sensors with hydrogel coating Xiaomei Liu a , ...
Application of Fiber bragg Grating Sensors on ...The center wavelength b of the reflected spectral...
Fiber Grating 暂无评价 22页 免费 Fiber- Op tic Bragg- G... 3页 免费 光栅传感fiber optic br... 10页 1下载券 A Fiber...
Fiber-Bragg-grating-based seismic geophone for_理学_高等教育_教育专区。Optical Engineering 45 8 , 084404 August 2006 Fiber-Bragg-grating-based seismic ...
Any change in the fiber grating’s properties, such as strain, pressure, temperature or vibration, will change the reflected Bragg wavelength [4-8]. ...
microstructured fiber Bragg grating refractive index ...According to the mode analysis of a double-... or cladding modes can easily interact with the ...
热门文档