文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 物理 > ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling
侵权投诉

ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling

ALE3D模拟慢烤

higher that the measured values with the assumption of incompressible deformation.

We apply a temperature at the outside boundary of the metal cylinder of 2o C/hour. Free convection losses to the air at the vessel wall are included using a heat transfer coefficient for laminar flow of air past a vertical plate. For both the method of slide surfaces and the gap material, the thermal transport properties of air are employed for the gap.

The mesh in the high explosive is smoothed using a combination of Lagrange and Eulerian algorithms. Nodes initially on the high explosive boundaries remain on these boundaries while nodes interior to the HE are advected through the HE species. The Lagrangian mesh movement strategy is applied in the steel.

After ignition of the LX-10, the burn front is followed using a level set method that conserves mass, momentum and energy across the front. Since the mesh is not moved to explicitly track the burn front, the resolution of the front is on the scale of the mesh element used. The effects of mesh size are an important consideration under current investigation.RESULTS

Gap Modeled with Slide Surfaces

First we consider the application of the method of slide surfaces to represent the closing of a gap between the explosive LX-10 and the steel cylinder for a 1D axisymmetric model of slow cookoff in a STEX experiment (see Figures 1, 4-9).

Figure 4 shows the mesh configuration, along with an initial 1 mm gap between the LX-10 and the steel vessel which has an inner diameter of 5.08 cm. The outside surface of the steel is heated at a slow rate of 2oC/hour which yields a nearly uniform temperature across the model domain until self-heating begins. The LX-10 with a coefficient of thermal expansion (CTE) of 54 m/m-oC expands more rapidly than the steel with a lower CTE of 12 m/m-oC. At temperatures between approximately n and noC, HMX_A (beta phase) is converting to the HMX_B (delta phase) which has a 6% lower density. Note that the model provides only an approximate representation of the actual HMX phase transition, which ooccurs over a few oC at approximately 160C as described above.

\

ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling

FIGURE 4. The initial mesh configuration with a 1.0 mm gap between the LX-10 (red) and the steel (blue). The gap between the HE and steel is treated using slide surfaces.

ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling

FIGURE 5. At a heating rate of 2oC/hour time the slide surface gap, initially 1 mm, between the HE (red) and steel (blue) has been reduced to 0.5 mm at 61.6 hours (Twall=143.2 C)

The gapis oreduced to 0.5 mm in 61.6 hours (Twall=143.2 C) as a result of of both thermal expansion and phase transition (see Figure 5). Figure 6 shows the gap close at 68.5 hours (Twall=157 C). At about the same time (67.9 h), a composition field plot for -HMX shows most of the -HMX has been transformed to -HMX (see Figure 7). There was no signification formation of product gases at this time so that the gap closure was due to thermal expansion and phase transition. At higher temperatures, self-heating and the

上一页第6页

TOP相关主题

你可能喜欢

热门文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email