文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 物理 > ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling
侵权投诉

ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling

ALE3D模拟慢烤

Table 2 Thermal properties for LX-10 species

v (g/cm3

)

(J/kgK)conductivity (W/mK)

HMX_A1.8652185.0.456HMX_B1.7552048.0.456HMX_C1.7552048.0.456HMX_D1.8651422.0.1317HMX_E1.8651422.0.1317VITON_A1.8652185.

ALE3D Simulations of Gap Closure and Surface Ignition for Cookoff Modeling

0.456The time-dependent thermal transport model includes the effects of conduction, reaction, advection, and compression. The constant-volume heat capacity is constant for each reactant consistent with the Steinberg-Guinan model. The thermal conductivity for the condensed species A and B are taken to be constant, whereas the effects of temperature are included for the gaseous species. The heat capacity for the gases is assigned the same constant-volume value used in the gamma-law model. The temperature dependent thermal conductivity is estimated at 1 kbar using Bridgman’s equation for liquids in which the sound velocity is calculated using results from CHEETAH.

The materials parameters of the decomposition model we assembled from measurements obtained for LX-10 samples investigated in earlier studies. Two sets of ODTX measurements were made for LX-10 using the standard apparatus at LLNL. The measurements of this study are plotted as a function of temperature in Figure 3.

Calculated explosion times for LX-10 are also shown in Figure 3 for a one-dimensional model involving transient heat conduction and the chemical reaction sequence for HMX (with Viton inert). The two sets of experimental measurements are well represented by the ALE3D thermo chemical model.

It is noted that although this model provides a good representation of the ODTX data, it does not adequately represent other types of behavior needed for accurate representation of other types of

behavior needed for accurate simulation of thermal transport, time to explosion and violence. Two areas of needed model improvement are in the areas of pressure effects and the phase transition for HMX.

FIGURE 3. Comparison of model and measured ODTX explosion times as a function of temperature for LX-10.

The decomposition of HMX has been observed to have a strong pressure dependence, which is not captured with the present kinetics models. Model decomposition rates are too large when the pressure is small. This decomposition rate strongly influences the vessel pressurization prior to ignition, which would be expected to affect the subsequence violence.

The phase transition is the second are needed model improvement. The model phase transition occurs over many ten of degrees (oC), while past measurements suggest a narrower temperature range. An accurate model for the phase transition is important for at least two reasons. The first is that the phase transition relates to a 6% decrease in density, which affects the closing of the gap between the high explosive and the steel. The phase transition also influences the burn behavior of LX-10, as the -phase material burns model more slowly that the -phase material.Numerical Method

Most of the previous simulations of slow and fast cookoff with ALE3D have been calculated with explicit hydrodynamics, using courant times and time steps scaled with a technique called “mass scaling”. This is a technique that explicit dynamics codes use to artifically raise the allowed time step above the normal Courant stability criterion. The

上一页第4页

TOP相关主题

你可能喜欢

热门文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email