文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > Development of an Exoskeleton Robot for Human
侵权投诉

Development of an Exoskeleton Robot for Human

外骨骼的很不错的国外论文

joints, the humeroradial joint and proximal radioulnar and crosses over the ulnar.

(a) Front view (b) Side view

Fig. 1 Wrist joint

The wrist holder is attached to link-2. The motor for wrist flexion/extension motion (Motor-2) is fixed on link-2. Link-2 is attached with L-shaped link attachment using a bearing and a shaft to form a revolute joint. The link attachment holds the motor for the wrist ulnar/radial deviation (Motor-3). Link-3 is attached to the link attachment using a shaft and bearing to form a revolute joint. The palm holder and a three axis force sensor are attached to link-3. The palm holder of the exoskeleton is attached to the palm of the user. The link attachment has been designed to provide the 5 mm deviation of the ulna/radial deviation axis and the flexion/extension axis. The effective length of the exoskeleton is 398 mm and the width is 167 mm at the most wide location.

Development of an Exoskeleton Robot for Human

III

HARDWARE DESIGN OF EXOSKELETON

A Mechanical Structure and Mechanism

The robot should be adaptable to the human wrist in terms of segmental lengths, range of motion and the number of DOFs. The axis deviation of the ulna/radial deviation axis and the flexion/extension axis is about 5 mm. The robot should provide the axis deviation and should be directly fixed to the human forearm. Since the robot is supposed to be used for everyday life of human subjects, its motion has to be flexible and smooth.

Figure 2 shows the proposed exoskeleton for human wrist and forearm motion assist. The proposed exoskeleton mainly consists of a forearm motion support part and a wrist motion support part, and it is directly attached to the user’s forearm. The wrist motion support part consists of a link attachment, two DC motors, two drive and driven bevel gear pairs (Gear ratio-1:2), a palm holder, a three axis force sensor and a link (LINK-3) which connect the palm holder and link attachment as shown in Fig. 2. The forearm motion support part consists of two links (LINK-1 and 2), a DC motor, a drive and driven spur gear pair (Gear ratio 1:3), a wrist holder, a forearm cover and a wrist force sensor (Strain gauges).

Proximal end of link-1 can be attached to the upper limb exoskeleton robot [3] which has been developed previously. Distal end of link-1 is attached to the outer housing of the forearm cover. The motor for pronation/supination motion (Motor-1) is attached in outer housing of forearm cover. The outer housing of forearm and inner hollow cylinder are assembled [Fig. 3 (a)] through two bearings (Open REALI-SLIM®-radial contact type) such a way that the forearm can be inserted to the hole of the hollow cylinder. Therefore, the inner hollow cylinder of the forearm cover can be rotated with respect to the fixed outer housing. Link-2 is

Development of an Exoskeleton Robot for Human

attached to the inner hollow cylinder of the forearm cover.

(a) Overall system

Development of an Exoskeleton Robot for Human

Development of an Exoskeleton Robot for Human

(b) Top view (Dorsal view) (c) Side view (Radial side)

Fig. 2 3DOF wrist and forearm motion power assist exoskeleton.

上一页第2页

TOP相关主题

你可能喜欢

热门文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email