外骨骼的很不错的国外论文
Development of an Exoskeleton Robot for Human
Wrist and Forearm Motion Assist
R. A. R. C Gopura, K. Kiguchi
Department of Advanced Systems Control Engineering, Faculty of Science and Engineering, Saga University, Japan
gopura@ieee.org, kiguchi@ieee.org
Abstract –Exoskeleton is an external structural mechanism This paper presents wrist anatomy toward the with joints and links corresponding to those of the human development of the robot and the hardware design of the body. It transmits torques from actuators through rigid exoskeleton (mechanical structure and mechanism, sensors exoskeletal links to the human joints when it is worn. We and actuators, power transmission and safety aspects) and have been developing exoskeleton robots for assisting the
potential control methods. Experiments have been
motion of physically weak individuals such as elderly or
performed to confirm that the exoskeleton is able to slightly disabled in daily life. In this paper we propose a three
generate the required motions. degree of freedom (3DOF) exoskeleton robot for the forearm
pronation/supination motion, wrist flexion/ extension motion
and ulnar/radial deviation. The paper describes wrist anatomy toward the development of the robot, the hardware design of the exoskeleton (mechanical structure and mechanism, sensors and actuators, power transmission and safety aspects) and potential control methods. Force control using force/torque sensors located at wrist and forearm and electromyographic (EMG) signals based control using skin surface EMG signals of forearm and wrist muscles are the potential control methods for the robot. Experiments have been performed to evaluate the proposed exoskeleton. Key Words: Exoskeleton, Power-Assist, Human Motion
II WRIST ANATOMY –TOWARD THE EXOSKELETON
I INTRODUCTION
In the society in which the birthrate is decreasing and
aging are progressing, it is important that physically weak individuals take care of themselves without the help of others. We have been developing exoskeletons [1]-[4] for motion assist of physically weak individuals such as elderly, injured, or disabled. The physically weak individuals would be able to take care of themselves with the help of the exoskeletons. The upper-limb motions (shoulder, elbow, and wrist motion) are especially important for people to perform daily activities. The exoskeletons for elbow motion assist [1], shoulder motion assist [2], upper-limb motion assist [3][5], elbow and forearm motion assist[4], and knee motion assist [6] have been proposed for daily use or rehabilitation up to the present. This paper presents an exoskeleton for assisting wrist flexion/extension, ulnar/radial deviation, and forearm pronation/supination motions for physically weak people since they are essential motions for the daily living activities. Some important daily activities, which involve wrist and forearm motion are brushing teeth, eating with spoon, eating from hand, pouring from bottle, opening a door, writing and painting, drinking from cup, washing face and neck, shaving, polishing surfaces, and using a wheel chair.
The wrist, or carpus, is a deformable anatomic entity that connects the hand to the forearm. This is a collection of eight carpal bones and the surrounding soft tissue structure. The wrist contains several joints, including the radiocarpal joint, several intercarpal joints, and five carpometacarpal joints. The radiocarpal joint is a condyloid, joint formed by the end of the radius and the three carpal bones: the scaphoid, the lunate, and the triquetrum. The intercarpal joints as well as the carpometacarpal joints except for the thumb are functionally similar to flat joints. The surface-on-surface movement is chiefly gliding. The movements of the carpal bones in the distal row approximate those of the hand. On the contrary, the motion of the carpal bones of the proximal row is not proportional to the hand motions. Taken as an entity, the joints are considered as one joint, called the wrist joint [7].
The wrist joint possesses 2 DOF, flexion-extension and ulna/radial deviation. Flexion is the bending of the wrist so the palm approaches the anterior surface of the forearm. The reverse movement is extension. Abduction, or radial deviation, is bending the wrist to the thumb side. The reverse movement is adduction, or ulnar deviation. Wrist motion is performed around an instantaneous center. The path of the centrode is small, however, customarily, the displacement of the instantaneous center of rotation is ignored and the rotation axes for the flexion-extension and ulna/radial deviation are considered fixed. The axes pass through the capitate, a carpal bone articulating with the third metacarpal. The rotation axes are offset. The ulna/radial deviation axis passes distally with regard to the flexion-extension axis by approximately 5 mm [8] [Fig. 1]. The axis of rotation extends from the center of the radial head in the elbow joint to the center of the distal ulnar. The axis is oblique to the longitudinal axis of the forearm. In supination, the radius and ulnar are parallel to each other. During pronation, the radius rotates in the two proximal
1-4244-1152-1/07/$25.00 ©2007 IEEE.
热门文档