文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > Controlling total spot power from holographic laser by superimposing a binary phase grating
侵权投诉

Controlling total spot power from holographic laser by superimposing a binary phase grating

BNS,空间光调制器,文献

18. S. H. Lee and D. G. Grier, “Robustness of holographic optical traps against phase scaling errors,” Opt. Express

13(19), 7458–7465 (2005), doc.guandang.net.

19. M. kereň, I. Richter, and P. Fiala, “Design and optimization considerations of multi-focus phase-only diffractive

elements,” Proc. SPIE 5182, 233–242 (2004), doc.guandang.net.

20. S. Serati and J. Harriman, “Spatial light modulator considerations for beam control in optical manipulation

applications,” Proc. SPIE 6326, 63262W, 63262W-11 (2006), doc.guandang.net.

21. L. Xu, L. Y. Wu, J. Zhang, and X. Liu, “Effect of phase valley on diffraction efficiency of liquid crystal optical

phased array,” Proc. SPIE 7133, 71333L, 71333L-8 (2008), doc.guandang.net.

22. L. Xu, J. Zhang, and L. Y. Wu, “Influence of phase delay profile on diffraction efficiency of liquid crystal optical

phased array,” Opt. Laser Technol. 41(4), 509–516 (2009), doc.guandang.net.

23. X. D. Xun and R. W. Cohn, “Phase calibration of spatially nonuniform spatial light modulators,” Appl. Opt.

43(35), 6400–6406 (2004), doc.guandang.net.

1. Introduction

Laser-based optical traps use radiation pressure proportional to the incident laser power to manipulate particles on microscopic scale [1]. Since phase-only spatial light modulators (SLMs) allow for dynamic modulation of wavefronts with high accuracy and resolution, it is a good choice to use them for holographic beam steering [2,3]. Some optimized characteristics of manipulation can be obtained if the power of multiple 3D spots focused from the holographic beam can be made controllable, for example, dissociated neurons can be moved as fast as possible and kept alive by just adjusting the power to an optimized value [4].

It can be seen from experiment results that if the total power of spots can be directly controlled by tuning the driver of a laser source [4], the stability of laser is poor, sometimes even its intensity profile can be changed [5]. So, such a tunable optical component as tunable attenuator [6], acousto-optical modulator [7], polarization attenuator and so on, is usually added in front of the laser source to produce a stable power-tunable laser, even a high-accuracy power control. For example, as a kind of polarization attenuator, a half-wave plate placed between two polarizers can be used to achieve an power accuracy, which is as high as 10 times the accuracy of a three-polarizer attenuator (0.001) [8]. However, the additional optical component incorporated inevitably causes an insertion loss, and makes the optical manipulation system more complex in structure. A SLM-based system would have a less power loss, simple structure, even better performance while the powers of spots can be individually controlled by the SLM via a computer generated hologram (CGH) algorithm. A modified spherical wave approach [9] can be used to directly obtain multiple 3D spots, and the power of these spots can be separately controlled using the coefficients used to describe the intensity of spots. However, an obvious intensity error can be seen from the simulated results. The relative intensity error can be kept below 5% through a large number of acceptable single-pixel changes in the refresh interval of a typical liquid crystal SLM (LCSLM) using Direct Search algorithm (DS) [10]. A higher accuracy needs a longer computing time.

Weighted Gerchberg-Saxton (GSW) [11] is proposed in recent years to generate arbitrary 3D spots, because of its efficiency higher than DS after only 10 iterations, which can be completed in about 7 ms [12] with the help of a consumer GPU. From the viewpoint of energy conservation, a dummy area [13] is needed for containing the unwanted power. So, we used a GSW [3] with a fixed dummy area to adjust the power of a single spot with a resolution of 0.002, as shown in Fig. 1. However, too many iterations are needed to support the real-time applications in this case. It would take a longer time to complete the power adjustment of multiple spots with the same resolution because more than one spot must be controlled. Boulder Nonlinear Systems (BNS), Inc. has now fabricated high-speed SLM at a switching frequency up to 500 Hz. So what we need most is to reduce the computing time needed for a high-accuracy algorithm. It is therefore proposed in this paper to superimpose a tunable binary phase grating [14] with a conventional phase-only hologram to control the total spot power with high accuracy to a random value for real-time optical manipulation without extra power loss by changing the phase depth of grating.

#141925 - $15.00 USDReceived 28 Jan 2011; revised 23 Mar 2011; accepted 10 Apr 2011; published 18 Apr 2011

(C) 2011 OSA25 April 2011 / Vol. 19, No. 9 / OPTICS EXPRESS 8499

上一页第2页

你可能喜欢

热门文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email