辛苦弄得,希望能对你有用处,带来方便
element model of a belt conveyor can be developed when only the longitudinal elastic response of the belt is of interest.
Since the length of the belt part between the drive pulley and the take-up pulley, Is, is negligible compared to the length of the total belt, L, these pulleys can mathematically be combined to one pulley as long as the mass inertia's of the pulleys of the take-up system are accounted for. Since the resistance forces encountered by the belt during motion vary from place to place depending on the exact local (maintenance) conditions and geometry of the belt conveyor, these forces are distributed along the length of the belt. In order to be able to determine the influence of these distributed forces on the motion of the belt, the belt is divided into a number of finite elements and the forces which act on that specific part of the belt are allocated to the corresponding, element. If the interest is in the longitudinal elastic response of the belt only then the belt is not discredited on those places where it is supported by a pulley which does not force its motion (slip possible). The last step in building, the model is to replace the belt's drive and tensioning system by two forces which represent the drive characteristic and the tension forces.
The exact interpretation of the finite elements depends on which resistance's and influences of the interaction between the belt and its supporting structure are taken into account and the mathematical description of the constitutive behavior of the belt material. Depending on this interpretation, the elements can be represented by a system of masses, springs and dashpots as is shown in Figure 1, [9], where such a system is given for one finite element with nodal points c and c+ 1. The springs K and dashpot H represent the visco-elastic behavior of the belt's tensile member, G represents the belt's variable longitudinal geometric stiffness produced by the vertical acting forces on the belt's cross section between two idlers, V represent the belts velocity

dependent resistance's.
Figure 1: Five element composite model [9].
3.1.1 NON LINEAR TRUSS ELEMENT
If only the longitudinal deformation of the belt is of interest then a truss element can be used to model the elastic response of the belt. A truss element as shown in Figure 2 has two nodal points, p and q, and four displacement parameters which determine the component vector x:
输送带毕业设计--外文翻译_英语学习_外语学习_教育专区。The Two-Dimensional Dynamic Behavior of Conveyor Belts Ir. G. Lodewijks, Delft University of Technol...
Improved Two-Dimensional Dynamic Batch Process Monitoring with Support Vector ...Actually, the dynamic behavior of the batch process may exist not only ...
An Experimental Investigation on the Dynamic Behavior of Step Motor Drives_专业资料。Junlfcaisniergadtmai 21)3_4 oraoMehnc gnei n otn2(024140 EnAuo ...
Effect of Nb on the dynamic recrystallization behavior of high-grade pipeline steels_专业资料。今日推荐 88份文档 2014年全国注册造价工程师...
Impact of dopants inGaN on the formation of two-dimensional_电子/电路_工程科技_专业资料。Appl. Phys. A 75, 387–389 (2002) / Digital Object Identi...
The Two-Dimensional Dynamic Behavior of Conveyor Belts 3.1.1 NON LINEAR TRUSS ELEMENT If only the longitudinal deformation of the belt is of interest ...
Statistical challenges in the analysis of two-dimensional difference gel ...dynamic range in concentrations; (2) subject-to-subject variability within ...
IFUP-TH 49/92 arXiv:hep-lat/9210011v1 8 Oct 1992 1/N Expansion of Two-Dimensional Models in the Scaling Region ? Massimo Campostrini and Paolo ...
Nonlinear Dynamic Behavior of an Oscillating Tip-Microlever System and Contrast at the Atom In this paper the dynamic behavior of an oscillating tip-...
Solution of the Euler equations on unstructured grids for two-dimensional compressible flow_工学_高等教育_教育专区。关于二维的非结构网格可压流动的求解...
热门文档