辛苦弄得,希望能对你有用处,带来方便
consists of finite elements in order to account for the variations of the resistance's and forces exerted on the belt. The global elastic response of the belt is made up by the elastic response of all its elements. These finite element models have been applied in computer software which can be used in the design stage of long belt-conveyor systems. This is called the dynamic (design) approach. Verification of the results of simulation has shown that software programs based on these kind of belt-models are quite successful in predicting the elastic response of the belt during starting and stopping, see for example [3] and [4].
The finite element models as mentioned above determine only the longitudinal elastic response of the belt. Therefore they fail in the accurate determination of:
the motion of the belt over the idlers and the pulleys
the dynamic drive phenomena
the bending resistance of the belt
the development of (shock) stress waves
the interaction between the belt sag and the propagation of longitudinal stress waves
the interaction between the idler and the belt
the influence of the belt speed on the stability of motion of the belt
the dynamic stresses in the belt during. passage of the belt over a (driven) pulley
the influence of parametric resonance of the belt due to the interaction between vibrations of the take up mass or eccentricities of the idlers and the transverse displacements of the belt
the development of standing transverse waves
the influence of the damping caused by bulk material and by the deformation of the cross- sectional area of the belt and bulk material during, passage of an idler
the lifting of the belt off the idlers in convex and concave curves
The transverse elastic response of the belt is often the cause of breakdowns in long belt-conveyor systems and should therefore be taken into account. The transverse response of a belt can be determined with special models as proposed in [5] and [6], but it is more convenient to extend the present finite element models with special elements which take this response into account.
3.1 THE BELT
A typical belt-conveyor geometry consisting of a drive pulley, a tail pulley, a vertical gravity take-up, a number of idlers and a plate support is shown in Figure 1. This geometry is taken as an example to illustrate how a finite
输送带毕业设计--外文翻译_英语学习_外语学习_教育专区。The Two-Dimensional Dynamic Behavior of Conveyor Belts Ir. G. Lodewijks, Delft University of Technol...
Improved Two-Dimensional Dynamic Batch Process Monitoring with Support Vector ...Actually, the dynamic behavior of the batch process may exist not only ...
An Experimental Investigation on the Dynamic Behavior of Step Motor Drives_专业资料。Junlfcaisniergadtmai 21)3_4 oraoMehnc gnei n otn2(024140 EnAuo ...
Effect of Nb on the dynamic recrystallization behavior of high-grade pipeline steels_专业资料。今日推荐 88份文档 2014年全国注册造价工程师...
Impact of dopants inGaN on the formation of two-dimensional_电子/电路_工程科技_专业资料。Appl. Phys. A 75, 387–389 (2002) / Digital Object Identi...
The Two-Dimensional Dynamic Behavior of Conveyor Belts 3.1.1 NON LINEAR TRUSS ELEMENT If only the longitudinal deformation of the belt is of interest ...
Statistical challenges in the analysis of two-dimensional difference gel ...dynamic range in concentrations; (2) subject-to-subject variability within ...
IFUP-TH 49/92 arXiv:hep-lat/9210011v1 8 Oct 1992 1/N Expansion of Two-Dimensional Models in the Scaling Region ? Massimo Campostrini and Paolo ...
Nonlinear Dynamic Behavior of an Oscillating Tip-Microlever System and Contrast at the Atom In this paper the dynamic behavior of an oscillating tip-...
Solution of the Euler equations on unstructured grids for two-dimensional compressible flow_工学_高等教育_教育专区。关于二维的非结构网格可压流动的求解...
热门文档