IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)
SFP Controller with Dual LDD InterfaceDS1876
Figure 3. Quick-Trip Sample Timing
Table 2. ADC Default Monitor Full-Scale Ranges

SIGNAL (UNITS)
Temperature (NC)VCC (V)
PMON1, PMON2 and BMON1, BMON2 (V)
+FS SIGNAL127.9966.55282.4997
+FS HEX7FFFFFF8FFF8
-FS SIGNAL
-12800
-FS HEX800000000000
corresponding alarms and warnings (TXP HI1, TXP LO1, TXP HI2, TXP LO2, BIAS HI1, and BIAS HI2) are asserted or deasserted.
After resetting, the device completes one QT cycle before making comparisons. The TXP LO quick-trip alarm updates its alarm bit, but does not create FETG until after TXDEXT. TXP HI and BIAS HI can also be con-figured to wait for TXDEXT; however, this can be disabled using QTHEXT_ (Table 02h, Register 88h).
Monitors and Fault Detection
Monitors
Monitoring functions on the DS1876 include six quick-trip comparators and six ADC channels. This monitoring combined with the alarm enables (Table 01h/05h) deter-mines when/if the DS1876 turns off DACs and triggers the TXFOUT and TXDOUT1, TXDOUT2 outputs. All the monitoring levels and interrupt masks are user program-mable.
Six Quick-Trip Monitors and Alarms
Six quick-trip monitors are provided to detect potential laser safety issues and LOS status. These monitor the following:
1) High Bias Current 1 (HBATH1), causing QT BIAS1 HI2) Low Transmit Power 1 (LTXP1), causing QT TXP1 LO3) High Transmit Power 1 (HTXP1), causing QT TXP1 HI4) High Bias Current 2 (HBATH2), causing QT BIAS2 HI5) Low Transmit Power 2 (LTXP2), causing QT TXP2 LO6) High Transmit Power 2 (HTXP2), causing QT TXP2 HI
The high and low transmit power quick-trip registers (HTXP1, HTXP2, LTXP1, and LTXP2) set the thresholds used to compare against the PMON1 and PMON2 volt-ages to determine if the transmit power is within speci-fication. The HBATH1 and HBATH2 QTs compare the BMON1 and BMON2 inputs (generally from the laser driver’s bias monitor output) against their threshold set-tings to determine if the present bias current is above specification. The bias and power QTs are routed to FETG through interrupt masks to allow combinations of these alarms to be used to trigger FETG. The bias and power QTs are directly connected to TXFOUT (see Figure 9). The user can program up to eight different temperature-indexed threshold levels for HBATH1 and HBATH2 (Table 06h, Registers E0h-E7h).
Six ADC Monitors and Alarms
The ADC monitors six channels that measure tem-perature (internal temp sensor), VCC, PMON1, PMON2, BMON1, and BMON2 using an analog multiplexer to measure them round-robin with a single ADC (see the ADC Timing section). The channels have a customer-programmable full-scale range, and all channels have a customer-programmable offset value that is factory pro-grammed to a default value (see Table 2). Additionally, PMON1, PMON2 and BMON1, BMON2 can right-shift results by up to 7 bits before the results are compared to alarm thresholds or read over the I2C bus. This allows customers with specified ADC ranges to calibrate the ADC full scale to a factor of 1/2n of their specified range to measure small signals. The DS1876 can then right-shift the results by n bits to maintain the bit weight of their specification.
14 _____________________________________________________________________________________
IC datasheet pdf-DS1877,pdf,datasheet,SFP Controller for Dual Rx Interface_信息与通信_工程科技_专业资料。IC datasheet pdf-DS1877,pdf,datasheet,SFP ...
IC datasheet pdf-ONET8531T,pdf(11.3Gbps ...ONET8531T With Dual Cathode PIN Diode Copyright ?...Products DSP Clocks and Timers Interface Logic ...
元器件交易网www.cecb2b.com Datasheet 8 Gbps Bi...(Duplex LC) Dual-fiber, bi-directional Class 1...2-wire Serial Interface Data Line (MOD-DEF2) ...
? Customer’s MAC should be setup for SGMII interface with Auto-Negotiation... IC datasheet pdf-DS187... 65页 免费 AN4138C(20G四通道SFP有... 20页 ...
datasheet 11页 免费 XFP模块电路设计 6页 1下载...Assembled with low EMI emissions IC and fully ...Interface GBIC 1000Base-X to 1000Base-T SFP-...
IC datasheet pdf-DS1876,... 69页 免费 AlGaNGaN+HEMT的研制 60页 免费 ... Normally Off AlGaNGaN Low-Density Drain HEMT (LDD-HEMT) With Enhanced ...
The resistor range for the laser current settings is optimized to interface with the DS1858 SFP controller IC. The MAX3735/MAX3735A provide transmit-...
interface Duplex LC connector Built-in digital ...Datasheet Digital Diagnostics Functions MRV’s SFP-...Controller (DDTC) inside the transceiver, which ...
dual-loop LDD, allowing one PC board layout to...APPLICATIONS 1×/2×/4× Fibre Channel SFP/SFF...Control with a Single-Ended Laser Interface Rev....
Datasheet MAX3735 - 2.7Gbps, Low-Power SFP Laser Drivers - Maxim ... settings is optimized to interface with the DS1858 SFP controller IC. ...
热门文档