A356 T4 heat treatment
76
B. Dang et al./ Materials and Design 57 (2014) 73–78
Fig. 4. Microstructure characterizations of as-cast A356 alloy solutionized at different temperatures for 15 min, 35 min, 60 min, 90 min and 120 min.
Fig. 5. The morphology of the enlarged eutectic Si subjected to different solution treatments.
hypereutectic Al–Si alloys, may exist in hypoeutectic alloys if exposed suf ciently high cooling rate, and meanwhile, the nano-scale Si particles, uniformly distributed in the Al matrix, usually take place after slight over-aging if Si is presented in excess after quenching[15]. So, both the dendritic eutectic Si and the nanoscale Si particles are related to the Si concentration in the matrix, which is in uenced by the solute trapping effect arising from high cooling rate. Applying EDS analysis for the as-cast sample by PTC method, the average concentration of Si in the Al matrix is measured as$2.2 wt.%, much higher than the maximum solubility of Si in Al, 1.65 wt.% at 575°C and 0.05 wt.% at room temperature, due to the Al–Si equilibrium phase diagram. In consistent with the above argument, a highly saturated Si in matrix is therefore formed. On the other hand, the transformed fraction ($68%, see Fig. 2) of the primary aluminum corresponds to a strong shrink, and may form an imaginary‘‘gas gap’’, which reduce the heat extraction rate of solidi cation in the post-solidi cation (denoted in Fig. 2) stage, thus lowering the cooling rate during post-solidi cation. This effect, de ned herein as the post-solidi cation heat effect, favours the formation of dendritic eutectic Si and Si precipitates. That is to say, subjected to the post-solidi cation heat effect, the saturated Si in the matrix is separated out to form partially the nano-scale S
i precipitates, and diffuse partially toward the crystallized eutectic Si through PFZ (see Fig. 3b), eventually resulting in branches of eutectic Si due to the anisotropic Si concentration and width of PFZ. From Fig. 4, subjected to solution treatment, all eutectic Si dendrite is rounded, i.e. hackly edges of eutectic Si disappear, and Si precipitate are not found within Al matrix any more. This implies that the nano-scale Si particles may mainly precipitate in the post-solidi cation stage, but the formation of dendritic eutectic Si may be probably ascribed to the Al-Si eutectic solidi cation (i.e. in a coupled growth manner) and the simply physical separation and diffusion of excess Si upon post-solidi cation. This typical microstructure is bene cial to the subsequent solution treatment (see Section 4.2). 4.2. Effect of re ned as-cast microstructure on optimum solution treatment
Fig. 6. Comparisons of the mean size of eutectic Si solutionized at different temperatures for different time.
Upon solution treatment for Al–Si–Mg alloy, modi cation of eutectic Si is essentially dominated by diffusion of Si atoms from the

Effect of heat treatment on microstructure and ...The LMD alloy was given a solution treatment at...The hardness of the samples was measured using a...
Effect of pre post T6 heat treatment on the ...of laser welded SSM cast A356 aluminium alloy R...Microstructure, hardness and tensile properties of ...
Influence of post-weld heat treatment on the microstructure and hardness of laser weld seams on The transformation induced plasticity (TRIP) steels effect ...
b titanium alloys after different heat treatment. ...alloy microstructure, and the effect of the ...Hardness tests were carried out using a Vickers ...
Effect of yttrium on the microstructure of a semi-solid A356 Al alloy_专业资料。Avll niea\^^sineic.oaieol t^n,cecdrtm abnn.ec 喜Sinerc ...
Effect of thermomechanical treatment on microstructure and hardness behavior of AZ63 magnesium a 隐藏>> Avibeolea all ni tanwww.cecdrc.osineitm et姆 AC7 ...
effect of manganese on the microstructure and ...The surface hardness was measured by Vickers ...Brooks, Heat Treatment, Structure and Properties ...
EFFECT OF COLD ROLLING ON THE MICROSTRUCTURE AND ...The initial hardness of the alloy increased with ...heat treatment distributed along grain boundaries or...
and micro-hardness of Cu-3.5wt.%Ti-0.1wt.%Zr-RE alloy were investigated after optimizing technics of plastic deformation and the heat treatment. ...
Effect of heat treatment on plasticity of Al-Zn-Mg alloy: Microstructure ...(Hv) was measured on samples using shimadzu HVM-2000 hardness, at a load...
热门文档