文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > IT/计算机 > 互联网 > CMOS Low Noise Amplifier
侵权投诉

CMOS Low Noise Amplifier

THlC-3 A 6 Watt Ka-Band MMlC Power Module Using MMlC Power Amplifiers D.L. Ingram, D.I. Stones, T.W. Huang, M. Nishimoto, H. Wang, M. Siddiqui, D. Tamura, J. Elliott, R. Lai, M. Biedenbender, H.C. Yen and B. Allen TRW, RF Product Center One Space Park, Redondo Beach, CA 90278

Abstract In this paper we present the development of a 6 Watt 24% PAE Ka-band power module with an ass'ociated power gain of 21.5 dB. The power module consists of a driver amplifier and two power amplifier chips. These MMlC amplifiers were fabricated with a 2-mil thick substrate using 0.1 5 y m InGaAs/AIGaAs/ GaAs HEMT technology. The driver amplifier is a fully matched single-ended design with an output power of 27.5 dBm, a 10.7 dB power gain and 27% PAE. We use a hybrid approach for the output power amplifier which consists of two partially-matched MMlC chips and a 8-way Wilkinson combiner fabricated on Alumina substrate. The MMlC power amplifiers delivered a record power of 35.4 dBm (3.5W) with a PAE of 28% and an associated power gain of 11.5 dB. The 8-way combiner has an insertion loss of 0.6 dB. We believe this is a new benchmark for power module using monolithic approach at this frequency range.

power density delivered by 2-mil device is at least 25-

35% better than the 4-mil device of similar periphery 111-[41, PI 171.

Design Driver Amplifier Fig. 1 shows the photo of the driver amplifier. The driver amlifier is a two-stage single-ended design with the output device periphery of 1.52 mm. Conservative device drive ratio was used to ensure enough power to drive the output stage over process variation. Harmonic terminations were provided at the drain to improve the PAE and these also help the out of band stability. This chip was fully matched to 50 ohm at the input and output. Stability analysis was done on both stages to make sure there was sufficient margin over process variation. Odd mode clamping resistors were inserted between FETs to suppress the push-pull oscillation. Odd mode stability analysis was done according to[ 101. Out of band oscillation was suppressed by resistively loaded quarterwave stubs. The chip can be biased from either side for flexibility of insertion into different power modules. The chip area is 4.0x1.5 mm.

Introduction There has been numerous reports on the monolithic power amplifier performance[ l] -[8]. The best power at Ka-band is about 1 W. This work benchmarks the state-of-the-art performance achieved by a single MMlC chip and a module using these chips as building blocks. 2-mil GaAs wafer offers the advantages of providing shorter thermal path and smaller via hole pattern to the back side, thus allowing multiple via holes to be inserted between gate fingers without increasing the pitch of the gate fingers. This multiple via holes to ground lowers the overall source inductance of the device. This will improve the gain and PAE of the amplifier especially at millimeter-wave frequency range. These multiple vias to ground also

subs

tantially improve the thermal dissipation of the heat generated per such small device area. Based on our past experience with 4-mil substrate designs, the

Figure 1. Photo of the driver amplifier MMIC chip ( 4 . 0~ 1 . 5" ) Power Amplifier Fig. 2 shows the photo of the power amplfier. The

1183 0-7803-3814-6l97l$5.00 0 IEEE 1997 IEEE MTT-S Digest

CMOS Low Noise Amplifier

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email