文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > Design of a Dual-Band Low Noise Amplifier
侵权投诉

Design of a Dual-Band Low Noise Amplifier

本文介绍了一种双带低噪声放大器DECT为1.8千兆赫无线局域网应用到24千兆赫的积极反馈技术

Design of a Dual-Band Low Noise Amplifier (LNA) Utilizing Positive Feedback Technique

Lini Lee1, Roslina Mohd Sidek1, S. S. Jamuar1 and Sabira Khatun2

1Department of Electrical & Electronic Engineering

Faculty of Engineering, Universiti Putra Malaysia

43400 UPM Serdang, Selangor, Malaysia

2Department of Computer System & Communication Engineering

Faculty of Engineering Universiti Putra Malaysia

43400 UPM Serdang, Selangor, Malaysia

Abstract-This paper presents a dual band low noise amplifier (LNA) for 1.8 GHz DECT and 2.4 GHz WLAN applications employing positive feedback technique. This LNA exploits a positive feedback capacitor connected to a conventional cascaded inductive source degenerated LNA whereby the connection of a capacitor determines the operating frequency of the LNA. For operation at 1.8 GHz DECT, the capacitor is feedback to both transistors of the cascaded LNA and as for 2.4 GHz WLAN application, the capacitor is feedback to only one of the transistors. Two switches are employed to control the connection of the feedback capacitor to the LNA. By switching the connection of the feedback capacitor, the narrow-band gain and impedance matching are achieved at both 1.8 GHz and 2.4 GHz frequency bands. The LNA has been simulated using 0.18 CMOS technology and results attained for both two bands are as followed; gain, S21 = 21 dB, noise figure, NF = 0.8 dB and linearity with third-order intercept point, IIP3 = -0.13 dBm. Simulation results prove that the technique works and a dual-band LNA with a chip size comparable to a single-band LNA is realized with the proposed topology.

Section II describes the dual-band LNA architecture and analysis involved. The simulation results are presented in Section III and finally, conclusions are given in Section IV. II. DUAL-BAND LNA ARCHITECTURE

Fig. 1 shows the schematic of the proposed dual-band LNA. The amplifier is similar to the conventional LNA described in [4] except for the feedback capacitor, Cf and two switches;S1 and S2. Transistors M1 and M2 form the cascode stage for the LNA. Inductors Lg,Ls and the gate-to-source capacitance of M1 (Cgs1) form the input tune circuit. The inductor, Ld combines with the capacitor, Cf to form a resonance circuit for the dual-band applications.

Index terms – dual band, low noise amplifier (LNA), multi-band, multimode, positive feedback capacitor.

I. INTRODUCTION

Progress in silicon IC technology [1] and innovations in IC design have enabled communication anywhere at anytime. The existence of different cellular systems requires multi-mode, multi-band and multi-standard mobile systems. Transceivers for multi-mode and multi-standard applications are most often implemented by replicating the receiver circuits for each operating band or standard [2]. This allows applications such as GSM or WCDMA to operate concurrently. Though this approach is simpler to implement, it is neither optimal in cost nor in power consumption [3].

In this work, a dual-band low noise amplifier (LNA) is presented. The proposed dual-band LNA works at 1.8 GHz for Digital Enhanced Cordless Telecommunications (DECT) and 2.4 GHz for Wireless Local Area Network (WLAN) applications. This dual-band LNA utilizes a positive feedback capacitor connection with switches in order to operate accordingly.

S2

S1

Fig. 1: The proposed dual-band LNA

Depending on the frequency band needed, for operation at 1.8 GHz DECT, the capacitor, Cf would be fedback to both the transistors of the cascaded LNA. When the frequency band of 2.4 GHz WLAN is needed, Cf would only be fedback to the

1-4244-0527-0/06/$20.00 © 2006 IEEE 22

第1页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email