文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 高等教育 > 文学 > 机械——模具设计的外文翻译
侵权投诉

机械——模具设计的外文翻译

我自己的翻译啊

simple two-plate molds which have a flat parting surface the fully round runner or

hexagonal runner is to be prefaced, the increased mod cost being relatively small. For

molds which have complex parting surface, where it would be difficult to match

accurately the semicircular channels of the round runner or, for multi-plate molds, the

trapezoidal or modified trapezoidal section should be used.

2.Runner size

When deciding the size of the runner the designer must consider the following

factors: (i) the wall section and volume of the molding (ii) the distance of the

impression from the main runner or sprue, (iii) runner cooling considerations, (iv) the

range of mouldmaker's cutters available and (v) the plastics material to be used.

(i) The cross-sectional area of the runner must be sufficient to permit the freezes

and for packing pressure to be applied for shrinkage compensation if required,

Because of this, runners below 2 mm (3/32 in) diameter are seldom used and even this

diameter is normally limited to branch runners under 25mm (1 in) in length.

(ii) The further the plastic melt has to travel alone the runner the greater is the

resistance to flow. Hence the distance the impression is from the sprue has a direct

bearing on the choice of cross-sectional size of the runner. For example, whereas a

5mm (3/16 in)

(iii) The cross-sectional area of the runner should not be such that it controls the

injection cycle, although this is sometimes unavoidable for very light moldings The

larger he cross-sec ~tion area of the runner the greater is the bulk of material it

contains and the longer the period it takes to cool sufficiently to enable the mod to be

opened and the moldings and runner ejected. For this reason it is undesirable to make

the runner larger than 10 mm (] in) diameter for most materials. However, the rigid

PVCs and the acrylics are exceptions due to their high viscosity and diameters up to

13 mm (1/2 in) are used.

(iv) The size chosen for the runner should be in a range consistent with the

mouldmakers's not having to carry in stock a multitude of different! sizes of cutters. In

practice the following are the more common sizes: 2-13 mm in I mm steps in the

metric range and ~-? in With ~ in steps in the imperial unit range. The following

empirical formula is suggested as a guide of the size of the runner or branch runner

for moldings weighing up to 200g(I g (7 oz), and with wall sections less than 3 mm

(0.125 in). For the rigid PVCs and the acrylics, increase the calculated diameter by

25%.

The formula is used in conjunction with the notes given previously.

(i) The runner should not be below 2 mm (3/32 in) diameter, nor above 10 mm (3/8

in) diameter (or 13 mm (1/2 in) diameter where applicable).

(ii) The calculated size should be increased to the next suitable cutter size

Figure 4.7 shows a plot of diameter versus length of runner for various weights of

molding, adopting the metric system of dimensioning. Figure 4.8 shows a

corresponding plot using the Imperial dimensioning system. For example, a 120 g (4

oz) molding in polyethylene being fed by a 50 mm (2 in) long runner will require a

diameter of 7 mm (5/16 in).

上一页第3页

你可能喜欢

热门文档

相关文档

  • 模具毕业设计外文翻译

    模具毕业设计外文翻译_机械/仪表_工程科技_专业资料。冷冲模具使用寿命的影响及对策 冲压模具概述 冲压模具--在冷冲压加工中,将材料(金属或非金属)加工成零件(或...

  • 注塑成型的模具设计外文翻译

    注塑成型的模具设计外文翻译_机械/仪表_工程科技_专业资料 暂无评价

  • 2011机械模具毕业设计英文翻译

    机械毕业设计英文翻译 5页 免费 机械及模具英文翻译 6页 免费 机械毕业设计...天津工程师范学院 2007 届本科生毕业设计 一种面向快速产品开发的新型集成系统 ...

  • 外文翻译模具设计与制造

    毕业设计(论文)外文资料翻译系 专姓学部: 业: 名: 号: Mold Design and Manufacture 机械工程 机械工程及自动化 外文出处: 外文出处: 附 1.外文资料翻译译文;...

  • 模具自动化技术 外文资料 外文翻译 毕业设计材料(英文...

    模具自动化技术 外文资料 外文翻译 毕业设计材料(英文在后面)_机械/仪表_工程科技_专业资料。模具自动化技术 欧盟(通过其所属各国政府的 EUREKE 计划)在 1998 ...

  • 注塑模具毕业设计外文翻译

    注塑模具毕业设计外文翻译_机械/仪表_工程科技_专业资料。附录外文资料与中文翻译 外文资料: China's mold industry and its development trend The mold is the ...

  • 材成专业模具毕业设计外文翻译

    材成专业模具毕业设计外文翻译_机械/仪表_工程科技_专业资料。注塑模外文翻译、单浇口优化分析景德镇陶瓷学院 毕业设计(论文)有关外文翻译 院专姓学 系: 业: 名...

  • 模具毕业设计的外文翻译

    模具毕业设计的外文翻译_工学_高等教育_教育专区。毕业设计,模具外文翻译...2.挤压铸造设备 铸造是现代机械制造工业的基础工艺之一。铸造作为一种金属热加工...

  • 塑料模具毕业设计外文翻译(附英文原文)

    塑料模具毕业设计外文翻译(附英文原文)_机械/仪表_工程科技_专业资料。毕业设计...一个描述电铸镍壳在注塑模具的应用的技术研究——Universidad de Las Palmas de ...

  • 【机械类文献翻译】冲压模具设计

    指导教师评语: 签名: 年月日 机械专业中英文文献翻译 附件 1:外文资料翻译译文 冲压模具设计 对 今日推荐 160份文档 2014年度细分行业报告汇集...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email