antenna, too.
正如上图所示,3D角反射器天线在抛物面F/D为0.9或更高时有很高的效率。原因是它的垂直方向角非常狭窄,换句话说,对于偏馈卫星电视抛物面天线来说,垂直方向角太狭窄了,而水平方向角又太宽了,如图所示。显然,3D角反射器天线也必须调整才能用于低F/D的偏馈抛物面,如果它的垂直方向图必须宽、水平方向图必须窄,那么垂直和水平两者之间必须大体平衡,而同时要保持天线的其它所有良好特性。因为加宽和缩窄方向图可能只需改变反射器的几何结构,那么改变反射器的尺寸和形状就是我做的另一道菜。无论如何,这个对称几何反射器形体的改变,可能会带来这个天线赖以运作的基本几何特性不稳定的危险。这也就意味着完全改变了天线的大部分实质性的宝贵的特性。 By small changes, actually by gradually removing the parts of the reflector responsible for vertical radiation beam narrowing, I succeeded in progressively widening the vertical diagram. At the same time, in order to narrow the horizontal radiation diagram, I increased the length of the sides of the reflector. With constant monitoring of the achieved results, I made the radiation diagram angles in both planes approximately equal, which is needed for efficient illumination of parabolas whose F/D is about 0.7-0.9. In the end, the result was the optimal diagram for the use with SAT TV offset parabolas. The input impedance of the antenna, the wideness of the frequency working range and purity of the diagram of the antenna remained practically unchanged.
通过小的改变,实际上是通过逐渐除去反射器造成垂直辐射波束狭窄的那部分,我成功地逐步加宽了垂直方向图,同时,为了缩窄水平方向图,我增加了反射器的边长。我边改造边监测改善的结果,我得到了适合F/D大约0.7-0.9的抛物面反射器需要的水平和垂直均衡的方向角,最终得到了用于偏馈卫星电视抛物面反射器天线的最佳方向图。天线的输入阻抗、工作频率的带宽和纯正的方向图几乎保持不变。
The vertical diagram, of the main beam in addition to widening, became much cleaner, which additionally improved the characteristics of the feed. The gain of the feed antenna is practically unchangeable (about 14.8 dBi), and input SWR is below 1.5:1 in the whole working range.
垂直方向图(除主束加宽之外)变得非常干净,改善了馈源的特性,在整个工作频段,馈源天线增益没有改变(大约14.8dBi),输入驻波比低于1.5:1 。


本文介绍用改进型3D角反射天线, 为6厘米业余无线电通信频段STA卫星电视 或WLAN频段5.8GHz频道的偏馈抛物面天线作馈源。 Introduction 引言 The problems that occur...
本文介绍用改进型3D角反射天线, 为6厘米业余无线电通信频段STA卫星电视 或WLAN频段5.8GHz频道的偏馈抛物面天线作馈源。 Introduction 引言 The problems that occur...
热门文档